diff --git a/CHANGELOG b/CHANGELOG
index 78f3da1..d038fb4 100644
--- a/CHANGELOG
+++ b/CHANGELOG
@@ -2,6 +2,9 @@
 Changes for U-Boot 1.1.4:
 ======================================================================
 
+* Add support for AMCC 440SP, add support for AMCC Luan 440SP eval board.
+  Patch by John Otken, 23 Nov 2005
+
 * Changed PPC44x startup message (cpu info, speed...) to common style:
   On PPC44x platforms, the startup message generated in "cpu.c" only
   comprised the ppc type and revision but not additional informations
diff --git a/CREDITS b/CREDITS
index c1686a5..f91fa3e 100644
--- a/CREDITS
+++ b/CREDITS
@@ -317,6 +317,10 @@
 D: Initial support for SSV-DNP1110, SMC91111 driver
 W: www.elinos.com
 
+N: John Otken
+E: jotken@softadvances.com
+D: Support for AMCC Luan 440SP board
+
 N: Tolunay Orkun
 E: torkun@nextio.com
 D: Support for Cogent CSB272 & CSB472 boards
diff --git a/MAINTAINERS b/MAINTAINERS
index d026417..845f4e7 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -240,6 +240,10 @@
 	csb272			PPC405GP
 	csb472			PPC405GP
 
+John Otken <jotken@softadvances.com>
+
+	luan			PPC440SP
+
 Keith Outwater <Keith_Outwater@mvis.com>
 
 	GEN860T			MPC860T
diff --git a/MAKEALL b/MAKEALL
index 7c5f1c1..64bec8a 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -68,12 +68,13 @@
 	csb472		DASA_SIM	DP405		DU405		\
 	ebony		ERIC		EXBITGEN	G2000		\
 	HH405		HUB405		JSE		KAREF		\
-	METROBOX	MIP405		MIP405T		ML2		\
-	ml300		ocotea		OCRTC		ORSG		\
-	p3p440		PCI405		PIP405		PLU405		\
-	PMC405	        PPChameleonEVB	sbc405		VOH405		\
-	VOM405          W7OLMC		W7OLMG		walnut		\
-	WUH405		XPEDITE1K	yellowstone	yosemite	\
+	luan		METROBOX	MIP405		MIP405T		\
+	ML2		ml300		ocotea		OCRTC		\
+	ORSG		p3p440		PCI405		PIP405		\
+	PLU405		PMC405	        PPChameleonEVB	sbc405		\
+	VOH405		VOM405          W7OLMC		W7OLMG		\
+	walnut		WUH405		XPEDITE1K	yellowstone	\
+	yosemite							\
 "
 
 #########################################################################
diff --git a/Makefile b/Makefile
index fdde4b9..5d65927 100644
--- a/Makefile
+++ b/Makefile
@@ -815,6 +815,9 @@
 KAREF_config: unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx karef sandburst
 
+luan_config:	unconfig
+	@./mkconfig $(@:_config=) ppc ppc4xx luan amcc
+
 METROBOX_config: unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx metrobox sandburst
 
diff --git a/board/amcc/luan/Makefile b/board/amcc/luan/Makefile
new file mode 100644
index 0000000..5654f91
--- /dev/null
+++ b/board/amcc/luan/Makefile
@@ -0,0 +1,48 @@
+#
+# (C) Copyright 2002
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	= $(BOARD).o
+OBJS   += flash.o
+SOBJS	= init.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################
diff --git a/board/amcc/luan/config.mk b/board/amcc/luan/config.mk
new file mode 100644
index 0000000..f52c206
--- /dev/null
+++ b/board/amcc/luan/config.mk
@@ -0,0 +1,44 @@
+#
+# (C) Copyright 2002
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# esd ADCIOP boards
+#
+
+#TEXT_BASE = 0x00001000
+
+ifeq ($(ramsym),1)
+TEXT_BASE = 0xFBD00000
+else
+TEXT_BASE = 0xFFFC0000
+endif
+
+PLATFORM_CPPFLAGS += -DCONFIG_440=1
+
+ifeq ($(debug),1)
+PLATFORM_CPPFLAGS += -DDEBUG
+endif
+
+ifeq ($(dbcr),1)
+PLATFORM_CPPFLAGS += -DCFG_INIT_DBCR=0x8cff0000
+endif
diff --git a/board/amcc/luan/epld.h b/board/amcc/luan/epld.h
new file mode 100644
index 0000000..05362e0
--- /dev/null
+++ b/board/amcc/luan/epld.h
@@ -0,0 +1,85 @@
+#define EPLD0_FSEL_FB2		0x80
+#define EPLD0_BOOT_SMALL_FLASH	0x40	/* 0 boot from large flash, 1 from small flash */
+#define EPLD0_RAW_CARD_BIT0	0x20	/* raw card EC level */
+#define EPLD0_RAW_CARD_BIT1	0x10
+#define EPLD0_RAW_CARD_BIT2	0x08
+#define EPLD0_EXT_ARB_SEL_N	0x04	/* 0 select on-board ext PCI-X, 1 internal arbiter */
+#define EPLD0_FLASH_ONBRD_N	0x02	/* 0 small flash/SRAM active, 1 block access */
+#define EPLD0_FLASH_SRAM_SEL_N	0x01	/* 0 SRAM at mem top, 1 small flash at mem top */
+
+#define EPLD1_CLK_CNTL0		0x80	/* FSEL-FB1 of MPC9772 */
+#define EPLD1_PCIX0_CNTL1	0x40	/* S*0 of 9531 */
+#define EPLD1_PCIX0_CNTL2	0x20	/* S*1 of 9531 */
+#define EPLD1_CLK_CNTL3		0x10	/* FSEL-B1 of MPC9772 */
+#define EPLD1_CLK_CNTL4		0x08	/* FSEL-B0 of MPC9772 */
+#define EPLD1_MASTER_CLOCK6	0x04	/* clock source select 6 */
+#define EPLD1_MASTER_CLOCK7	0x02	/* clock source select 7 */
+#define EPLD1_MASTER_CLOCK8	0x01	/* clock source select 8 */
+
+#define EPLD2_ETH_MODE_10	0x80	/* Ethernet mode 10   (default = 1) */
+#define EPLD2_ETH_MODE_100	0x40	/* Ethernet mode 100  (default = 1) */
+#define EPLD2_ETH_MODE_1000	0x20	/* Ethernet mode 1000 (default = 1) */
+#define EPLD2_ETH_DUPLEX_MODE	0x10	/* Ethernet force full duplex mode */
+#define EPLD2_RESET_ETH_N	0x08	/* Ethernet reset (default = 1) */
+#define EPLD2_ETH_AUTO_NEGO	0x04	/* Ethernet auto negotiation */
+#define EPLD2_DEFAULT_UART_N	0x01	/* 0 select DSR DTR for UART1 */
+
+#define EPLD3_STATUS_LED4	0x08	/* status LED 8 (1 = LED on) */
+#define EPLD3_STATUS_LED3	0x04	/* status LED 4 (1 = LED on) */
+#define EPLD3_STATUS_LED2	0x02	/* status LED 2 (1 = LED on) */
+#define EPLD3_STATUS_LED1	0x01	/* status LED 1 (1 = LED on) */
+
+#define EPLD4_PCIX0_VTH1	0x80	/* PCI-X 0 VTH1 status */
+#define EPLD4_PCIX0_VTH2	0x40	/* PCI-X 0 VTH2 status */
+#define EPLD4_PCIX0_VTH3	0x20	/* PCI-X 0 VTH3 status */
+#define EPLD4_PCIX0_VTH4	0x10	/* PCI-X 0 VTH4 status */
+#define EPLD4_PCIX1_VTH1	0x08	/* PCI-X 1 VTH1 status */
+#define EPLD4_PCIX1_VTH2	0x04	/* PCI-X 1 VTH2 status */
+#define EPLD4_PCIX1_VTH3	0x02	/* PCI-X 1 VTH3 status */
+#define EPLD4_PCIX1_VTH4	0x01	/* PCI-X 1 VTH4 status */
+
+#define EPLD5_PCIX0_INT0	0x80	/* PCIX0 INT0 status, write 0 to reset */
+#define EPLD5_PCIX0_INT1	0x40	/* PCIX0 INT1 status, write 0 to reset */
+#define EPLD5_PCIX0_INT2	0x20	/* PCIX0 INT2 status, write 0 to reset */
+#define EPLD5_PCIX0_INT3	0x10	/* PCIX0 INT3 status, write 0 to reset */
+#define EPLD5_PCIX1_INT0	0x08	/* PCIX1 INT0 status, write 0 to reset */
+#define EPLD5_PCIX1_INT1	0x04	/* PCIX1 INT1 status, write 0 to reset */
+#define EPLD5_PCIX1_INT2	0x02	/* PCIX1 INT2 status, write 0 to reset */
+#define EPLD5_PCIX1_INT3	0x01	/* PCIX1 INT3 status, write 0 to reset */
+
+#define EPLD6_PCIX0_RESET_CTL	0x80	/* 0=enable slot reset, 1=disable slot reset */
+#define EPLD6_PCIX1_RESET_CTL	0x40	/* 0=enable slot reset, 1=disable slot reset */
+#define EPLD6_ETH_INT_MODE	0x20	/* 0=IRQ5 recv's external eth int */
+#define EPLD6_PCIX2_RESET_CTL	0x10	/* 0=enable slot reset, 1=disable slot reset */
+#define EPLD6_PCI1_CLKCNTL1	0x80	/* PCI1 clock control S*0 of 9531 */
+#define EPLD6_PCI1_CLKCNTL2	0x40	/* PCI1 clock control S*1 of 9531 */
+#define EPLD6_PCI2_CLKCNTL1	0x20	/* PCI2 clock control S*0 of 9531 */
+#define EPLD6_PCI2_CLKCNTL2	0x10	/* PCI2 clock control S*1 of 9531 */
+
+#define EPLD7_VTH1		0x80	/* PCI2 VTH1 status */
+#define EPLD7_VTH2		0x40	/* PCI2 VTH2 status */
+#define EPLD7_VTH3		0x20	/* PCI2 VTH3 status */
+#define EPLD7_VTH4		0x10	/* PCI2 VTH4 status */
+#define EPLD7_INTA_MODE		0x80	/* see S5 on SW2 for details */
+#define EPLD7_PCI_INT_MODE_N	0x40	/* see S1 on SW2 for details */
+#define EPLD7_WRITE_ENABLE_GPIO	0x20	/* see S2 on SW2 for details */
+#define EPLD7_WRITE_ENABLE_INT	0x10	/* see S3 on SW2 for details */
+
+
+typedef struct {
+    unsigned char  status;		/* misc status */
+    unsigned char  clock;		/* clock status, PCI-X clock control */
+    unsigned char  ethuart;		/* Ethernet, UART status */
+    unsigned char  leds;		/* LED register */
+    unsigned char  vth01;		/* PCI0, PCI1 VTH register */
+    unsigned char  pciints;		/* PCI0, PCI1 interrupts */
+    unsigned char  pci2;		/* PCI2 interrupts, clock control */
+    unsigned char  vth2;		/* PCI2 VTH register */
+    unsigned char  filler1[4096-8];
+    unsigned char  gpio00;		/* GPIO bits  0-7 */
+    unsigned char  gpio08;		/* GPIO bits  8-15 */
+    unsigned char  gpio16;		/* GPIO bits 16-23 */
+    unsigned char  gpio24;		/* GPIO bits 24-31 */
+    unsigned char  filler2[4096-4];
+    unsigned char  version;		/* EPLD version */
+} epld_t;
diff --git a/board/amcc/luan/flash.c b/board/amcc/luan/flash.c
new file mode 100644
index 0000000..d3c3c0d
--- /dev/null
+++ b/board/amcc/luan/flash.c
@@ -0,0 +1,111 @@
+/*
+ * (C) Copyright 2002
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2002 Jun Gu <jung@artesyncp.com>
+ * Add support for Am29F016D and dynamic switch setting.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * Modified 4/5/2001
+ * Wait for completion of each sector erase command issued
+ * 4/5/2001
+ * Chris Hallinan - DS4.COM, Inc. - clh@net1plus.com
+ */
+
+#include <common.h>
+#include <ppc4xx.h>
+#include <asm/processor.h>
+
+#undef DEBUG
+#ifdef DEBUG
+#define DEBUGF(x...) printf(x)
+#else
+#define DEBUGF(x...)
+#endif				/* DEBUG */
+
+static unsigned long flash_addr_table[1][CFG_MAX_FLASH_BANKS] = {
+	{0xff900000, 0xff980000, 0xffc00000},	/* 0:000: configuraton 3 */
+};
+
+/*
+ * include common flash code (for amcc boards)
+ */
+#include "../common/flash.c"
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+static ulong flash_get_size(vu_long * addr, flash_info_t * info);
+
+unsigned long flash_init(void)
+{
+	unsigned long total_b = 0;
+	unsigned long size_b[CFG_MAX_FLASH_BANKS];
+	unsigned short index = 0;
+	int i;
+
+	/* read FPGA base register FPGA_REG0 */
+
+	DEBUGF("\n");
+	DEBUGF("FLASH: Index: %d\n", index);
+
+	/* Init: no FLASHes known */
+	for (i = 0; i < CFG_MAX_FLASH_BANKS; ++i) {
+		flash_info[i].flash_id = FLASH_UNKNOWN;
+		flash_info[i].sector_count = -1;
+		flash_info[i].size = 0;
+
+		/* check whether the address is 0 */
+		if (flash_addr_table[index][i] == 0) {
+			continue;
+		}
+
+		/* call flash_get_size() to initialize sector address */
+		size_b[i] = flash_get_size((vu_long *)
+					   flash_addr_table[index][i],
+					   &flash_info[i]);
+		flash_info[i].size = size_b[i];
+		if (flash_info[i].flash_id == FLASH_UNKNOWN) {
+			printf("## Unknown FLASH on Bank %d - Size = 0x%08lx = %ld MB\n",
+			       i, size_b[i], size_b[i] << 20);
+			flash_info[i].sector_count = -1;
+			flash_info[i].size = 0;
+		}
+
+		/* Monitor protection ON by default */
+		(void)flash_protect(FLAG_PROTECT_SET, CFG_MONITOR_BASE,
+				    CFG_MONITOR_BASE + CFG_MONITOR_LEN - 1,
+				    &flash_info[2]);
+#ifdef CFG_ENV_IS_IN_FLASH
+		(void)flash_protect(FLAG_PROTECT_SET, CFG_ENV_ADDR,
+				    CFG_ENV_ADDR + CFG_ENV_SECT_SIZE - 1,
+				    &flash_info[2]);
+		(void)flash_protect(FLAG_PROTECT_SET, CFG_ENV_ADDR_REDUND,
+				    CFG_ENV_ADDR_REDUND + CFG_ENV_SECT_SIZE - 1,
+				    &flash_info[2]);
+#endif
+
+		total_b += flash_info[i].size;
+	}
+
+	return total_b;
+}
diff --git a/board/amcc/luan/init.S b/board/amcc/luan/init.S
new file mode 100644
index 0000000..7830ebd
--- /dev/null
+++ b/board/amcc/luan/init.S
@@ -0,0 +1,132 @@
+/*
+*
+* See file CREDITS for list of people who contributed to this
+* project.
+*
+* This program is free software; you can redistribute it and/or
+* modify it under the terms of the GNU General Public License as
+* published by the Free Software Foundation; either version 2 of
+* the License, or (at your option) any later version.
+*
+* This program is distributed in the hope that it will be useful,
+* but WITHOUT ANY WARRANTY; without even the implied warranty of
+* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+* GNU General Public License for more details.
+*
+* You should have received a copy of the GNU General Public License
+* along with this program; if not, write to the Free Software
+* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+* MA 02111-1307 USA
+*/
+
+#include <ppc_asm.tmpl>
+#include <config.h>
+
+/* General */
+#define TLB_VALID   0x00000200
+
+/* Supported page sizes */
+
+#define SZ_1K	    0x00000000
+#define SZ_4K	    0x00000010
+#define SZ_16K	    0x00000020
+#define SZ_64K	    0x00000030
+#define SZ_256K	    0x00000040
+#define SZ_1M	    0x00000050
+#define SZ_16M	    0x00000070
+#define SZ_256M	    0x00000090
+
+/* Storage attributes */
+#define SA_W	    0x00000800	    /* Write-through */
+#define SA_I	    0x00000400	    /* Caching inhibited */
+#define SA_M	    0x00000200	    /* Memory coherence */
+#define SA_G	    0x00000100	    /* Guarded */
+#define SA_E	    0x00000080	    /* Endian */
+
+/* Access control */
+#define AC_X	    0x00000024	    /* Execute */
+#define AC_W	    0x00000012	    /* Write */
+#define AC_R	    0x00000009	    /* Read */
+
+/* Some handy macros */
+
+#define EPN(e)		((e) & 0xfffffc00)
+#define TLB0(epn,sz)	( (EPN((epn)) | (sz) | TLB_VALID ) )
+#define TLB1(rpn,erpn)	( ((rpn)&0xfffffc00) | (erpn) )
+#define TLB2(a)		( (a)&0x00000fbf )
+
+#define tlbtab_start\
+	mflr    r1  ;\
+	bl 0f	    ;
+
+#define tlbtab_end\
+	.long 0, 0, 0	;   \
+0:	mflr    r0	;   \
+	mtlr    r1	;   \
+	blr		;
+
+#define tlbentry(epn,sz,rpn,erpn,attr)\
+	.long TLB0(epn,sz),TLB1(rpn,erpn),TLB2(attr)
+
+
+/**************************************************************************
+ * TLB TABLE
+ *
+ * This table is used by the cpu boot code to setup the initial tlb
+ * entries. Rather than make broad assumptions in the cpu source tree,
+ * this table lets each board set things up however they like.
+ *
+ *  Pointer to the table is returned in r1
+ *
+ *************************************************************************/
+
+    .section .bootpg,"ax"
+    .globl tlbtab
+
+tlbtab:
+    tlbtab_start
+
+#if (CFG_LARGE_FLASH == 0xffc00000)	/* if booting from large flash */
+    /* large flash */
+    tlbentry( 0xffc00000,         SZ_1M, 0xffc00000,          1, AC_R|AC_W|AC_X|SA_G|SA_I|SA_W )
+    tlbentry( 0xffd00000,         SZ_1M, 0xffd00000,          1, AC_R|AC_W|AC_X|SA_G|SA_I|SA_W )
+    tlbentry( 0xffe00000,         SZ_1M, 0xffe00000,          1, AC_R|AC_W|AC_X|SA_G|SA_I|SA_W )
+    tlbentry( 0xfff00000,         SZ_1M, 0xfff00000,          1, AC_R|AC_W|AC_X|SA_G|SA_I|SA_W )
+
+    tlbentry( 0xff800000,         SZ_1M, 0xff800000,          1, AC_R|AC_W|AC_X|SA_G/*|SA_I*/ )
+    tlbentry( 0xff900000,         SZ_1M, 0xff900000,          1, AC_R|AC_W|AC_X|SA_G|SA_I|SA_W )
+#else					/* else booting from small flash */
+    tlbentry( 0xffe00000,         SZ_1M, 0xffe00000,          1, AC_R|AC_W|AC_X|SA_G/*|SA_I*/ )
+    tlbentry( 0xfff00000,         SZ_1M, 0xfff00000,          1, AC_R|AC_W|AC_X|SA_G/*|SA_I*/ )
+
+    tlbentry( 0xff800000,         SZ_1M, 0xff800000,          1, AC_R|AC_W|AC_X|SA_G/*|SA_I*/ )
+    tlbentry( 0xff900000,         SZ_1M, 0xff900000,          1, AC_R|AC_W|AC_X|SA_G/*|SA_I*/ )
+    tlbentry( 0xffa00000,         SZ_1M, 0xffa00000,          1, AC_R|AC_W|AC_X|SA_G/*|SA_I*/ )
+    tlbentry( 0xffb00000,         SZ_1M, 0xffb00000,          1, AC_R|AC_W|AC_X|SA_G/*|SA_I*/ )
+#endif
+
+    tlbentry( CFG_EPLD_BASE,    SZ_256K, 0xff000000,          1, AC_R|AC_W|SA_G|SA_I )
+
+#if (CFG_SRAM_BASE != 0)		/* if SRAM up high and SDRAM at zero */
+    tlbentry( 0x00000000, SZ_256M, 0x00000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I )
+    tlbentry( 0x10000000, SZ_256M, 0x10000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I )
+#elif (CFG_SMALL_FLASH == 0xff900000)	/* else SRAM at 0 */
+    tlbentry( 0x00000000,   SZ_1M, 0xff800000, 1, AC_R|AC_W|AC_X|SA_G/*|SA_I*/ )
+#elif (CFG_SMALL_FLASH == 0xfff00000)
+    tlbentry( 0x00000000,   SZ_1M, 0xffe00000, 1, AC_R|AC_W|AC_X|SA_G/*|SA_I*/ )
+#else
+    #error DONT KNOW SRAM LOCATION
+#endif
+
+    /* internal ram (l2 cache) */
+    tlbentry( CFG_ISRAM_BASE,    SZ_256K, 0x80000000,      0, AC_R|AC_W|AC_X|SA_I )
+
+    /* peripherals at f0000000 */
+    tlbentry( CFG_PERIPHERAL_BASE, SZ_4K, CFG_PERIPHERAL_BASE, 1, AC_R|AC_W|SA_G|SA_I )
+
+    /* PCI */
+#if (CONFIG_COMMANDS & CFG_CMD_PCI)
+    tlbentry( CFG_PCI_BASE,    SZ_256M, 0x00000000, 9, AC_R|AC_W|SA_G|SA_I )
+    tlbentry( CFG_PCI_MEMBASE, SZ_256M, 0x10000000, 9, AC_R|AC_W|SA_G|SA_I )
+#endif
+    tlbtab_end
diff --git a/board/amcc/luan/luan.c b/board/amcc/luan/luan.c
new file mode 100644
index 0000000..c6b79a9
--- /dev/null
+++ b/board/amcc/luan/luan.c
@@ -0,0 +1,458 @@
+/*
+ * (C) Copyright 2005
+ * John Otken, jotken@softadvances.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <ppc4xx.h>
+#include <asm/processor.h>
+#include <spd_sdram.h>
+#include "epld.h"
+
+
+extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */
+
+
+/*************************************************************************
+ *  int board_early_init_f()
+ *
+ ************************************************************************/
+int board_early_init_f(void)
+{
+	volatile epld_t *x = (epld_t *) CFG_EPLD_BASE;
+
+	mtebc( pb0ap,  0x03800000 );	/* set chip selects */
+	mtebc( pb0cr,  0xffc58000 );	/* ebc0_b0cr, 4MB at 0xffc00000 CS0 */
+	mtebc( pb1ap,  0x03800000 );
+	mtebc( pb1cr,  0xff018000 );	/* ebc0_b1cr, 1MB at 0xff000000 CS1 */
+	mtebc( pb2ap,  0x03800000 );
+	mtebc( pb2cr,  0xff838000 );	/* ebc0_b2cr, 2MB at 0xff800000 CS2 */
+
+	mtdcr( uic1sr, 0xffffffff );	/* Clear all interrupts */
+	mtdcr( uic1er, 0x00000000 );	/* disable all interrupts */
+	mtdcr( uic1cr, 0x00000000 );	/* Set Critical / Non Critical interrupts */
+	mtdcr( uic1pr, 0x7fff83ff );	/* Set Interrupt Polarities */
+	mtdcr( uic1tr, 0x001f8000 );	/* Set Interrupt Trigger Levels */
+	mtdcr( uic1vr, 0x00000001 );	/* Set Vect base=0,INT31 Highest priority */
+	mtdcr( uic1sr, 0x00000000 );	/* clear all interrupts */
+	mtdcr( uic1sr, 0xffffffff );
+
+	mtdcr( uic0sr, 0xffffffff );	/* Clear all interrupts */
+	mtdcr( uic0er, 0x00000000 );	/* disable all interrupts excepted cascade */
+	mtdcr( uic0cr, 0x00000001 );	/* Set Critical / Non Critical interrupts */
+	mtdcr( uic0pr, 0xffffffff );	/* Set Interrupt Polarities */
+	mtdcr( uic0tr, 0x01000004 );	/* Set Interrupt Trigger Levels */
+	mtdcr( uic0vr, 0x00000001 );	/* Set Vect base=0,INT31 Highest priority */
+	mtdcr( uic0sr, 0x00000000 );	/* clear all interrupts */
+	mtdcr( uic0sr, 0xffffffff );
+
+	x->ethuart &= ~EPLD2_RESET_ETH_N; /* put Ethernet+PHY in reset */
+
+	return  0;
+}
+
+
+/*************************************************************************
+ *  int misc_init_r()
+ *
+ ************************************************************************/
+int misc_init_r(void)
+{
+	volatile epld_t *x = (epld_t *) CFG_EPLD_BASE;
+	x->ethuart |= EPLD2_RESET_ETH_N; /* take Ethernet+PHY out of reset */
+
+	return  0;
+}
+
+
+/*************************************************************************
+ *  int checkboard()
+ *
+ ************************************************************************/
+int checkboard(void)
+{
+	char *s = getenv("serial#");
+
+	printf("Board: Luan - AMCC PPC440SP Evaluation Board");
+
+	if (s != NULL) {
+		puts(", serial# ");
+		puts(s);
+	}
+	putc('\n');
+
+	return  0;
+}
+
+
+/*************************************************************************
+ *  long int fixed_sdram()
+ *
+ ************************************************************************/
+static long int fixed_sdram(void)
+{					/* DDR2 init from BDI2000 script */
+	mtdcr( 0x10, 0x00000021 );	/* MCIF0_MCOPT2 - zero DCEN bit */
+	mtdcr( 0x11, 0x84000000 );
+	mtdcr( 0x10, 0x00000020 );	/* MCIF0_MCOPT1 - no ECC, 64 bits, 4 banks, DDR2 */
+	mtdcr( 0x11, 0x2D122000 );
+	mtdcr( 0x10, 0x00000026 );	/* MCIF0_CODT  - die termination on */
+	mtdcr( 0x11, 0x00800026 );
+	mtdcr( 0x10, 0x00000081 );	/* MCIF0_WRDTR - Write DQS Adv 90 + Fractional DQS Delay */
+	mtdcr( 0x11, 0x82000800 );
+	mtdcr( 0x10, 0x00000080 );	/* MCIF0_CLKTR - advance addr clock by 180 deg */
+	mtdcr( 0x11, 0x80000000 );
+	mtdcr( 0x10, 0x00000040 );	/* MCIF0_MB0CF - turn on CS0, N x 10 coll */
+	mtdcr( 0x11, 0x00000201 );
+	mtdcr( 0x10, 0x00000044 );	/* MCIF0_MB1CF - turn on CS0, N x 10 coll */
+	mtdcr( 0x11, 0x00000201 );
+	mtdcr( 0x10, 0x00000030 );	/* MCIF0_RTR   - refresh every 7.8125uS */
+	mtdcr( 0x11, 0x08200000 );
+	mtdcr( 0x10, 0x00000085 );	/* MCIF0_SDTR1 - timing register 1 */
+	mtdcr( 0x11, 0x80201000 );
+	mtdcr( 0x10, 0x00000086 );	/* MCIF0_SDTR2 - timing register 2 */
+	mtdcr( 0x11, 0x42103242 );
+	mtdcr( 0x10, 0x00000087 );	/* MCIF0_SDTR3 - timing register 3 */
+	mtdcr( 0x11, 0x0C100D14 );
+	mtdcr( 0x10, 0x00000088 );	/* MCIF0_MMODE - CAS is 4 cycles */
+	mtdcr( 0x11, 0x00000642 );
+	mtdcr( 0x10, 0x00000089 );	/* MCIF0_MEMODE - diff DQS disabled */
+	mtdcr( 0x11, 0x00000400 );	/*		  ODT term disabled */
+
+	mtdcr( 0x10, 0x00000050 );	/* MCIF0_INITPLR0 - NOP */
+	mtdcr( 0x11, 0x81b80000 );
+	mtdcr( 0x10, 0x00000051 );	/* MCIF0_INITPLR1 - PRE */
+	mtdcr( 0x11, 0x82100400 );
+	mtdcr( 0x10, 0x00000052 );	/* MCIF0_INITPLR2 - EMR2 */
+	mtdcr( 0x11, 0x80820000 );
+	mtdcr( 0x10, 0x00000053 );	/* MCIF0_INITPLR3 - EMR3 */
+	mtdcr( 0x11, 0x80830000 );
+	mtdcr( 0x10, 0x00000054 );	/* MCIF0_INITPLR4 - EMR DLL ENABLE */
+	mtdcr( 0x11, 0x80810000 );
+	mtdcr( 0x10, 0x00000055 );	/* MCIF0_INITPLR5 - MR DLL RESET */
+	mtdcr( 0x11, 0x80800542 );
+	mtdcr( 0x10, 0x00000056 );	/* MCIF0_INITPLR6 - PRE */
+	mtdcr( 0x11, 0x82100400 );
+	mtdcr( 0x10, 0x00000057 );	/* MCIF0_INITPLR7 - refresh */
+	mtdcr( 0x11, 0x99080000 );
+	mtdcr( 0x10, 0x00000058 );	/* MCIF0_INITPLR8 */
+	mtdcr( 0x11, 0x99080000 );
+	mtdcr( 0x10, 0x00000059 );	/* MCIF0_INITPLR9 */
+	mtdcr( 0x11, 0x99080000 );
+	mtdcr( 0x10, 0x0000005A );	/* MCIF0_INITPLR10 */
+	mtdcr( 0x11, 0x99080000 );
+	mtdcr( 0x10, 0x0000005B );	/* MCIF0_INITPLR11 - MR */
+	mtdcr( 0x11, 0x80800442 );
+	mtdcr( 0x10, 0x0000005C );	/* MCIF0_INITPLR12 - EMR OCD Default */
+	mtdcr( 0x11, 0x80810380 );
+	mtdcr( 0x10, 0x0000005D );	/* MCIF0_INITPLR13 - EMR OCD exit */
+	mtdcr( 0x11, 0x80810000 );
+	udelay( 10*1000 );
+
+	mtdcr( 0x10, 0x00000021 );	/* MCIF0_MCOPT2 - execute preloaded init */
+	mtdcr( 0x11, 0x28000000 );	/*		  set DC_EN */
+	udelay( 100*1000 );
+
+	mtdcr( 0x40, 0x0000F800 );	/* MQ0_B0BAS: base addr 00000000 / 256MB */
+	mtdcr( 0x41, 0x1000F800 );	/* MQ0_B1BAS: base addr 10000000 / 256MB */
+
+	mtdcr( 0x10, 0x00000078 );	/* MCIF0_RDCC - auto set read stage */
+	mtdcr( 0x11, 0x00000000 );
+	mtdcr( 0x10, 0x00000070 );	/* MCIF0_RQDC - read DQS delay control */
+	mtdcr( 0x11, 0x8000003A );	/*		enabled, frac DQS delay */
+	mtdcr( 0x10, 0x00000074 );	/* MCIF0_RFDC - two clock feedback delay */
+	mtdcr( 0x11, 0x00000200 );
+
+	return  512 << 20;
+}
+
+
+/*************************************************************************
+ *  long int initdram
+ *
+ ************************************************************************/
+long int initdram( int board_type )
+{
+	long dram_size = 0;
+
+#if defined(CONFIG_SPD_EEPROM)
+	dram_size = spd_sdram (0);
+#else
+	dram_size = fixed_sdram ();
+#endif
+
+	return  dram_size;
+}
+
+
+/*************************************************************************
+ *  int testdram()
+ *
+ ************************************************************************/
+#if defined(CFG_DRAM_TEST)
+int testdram(void)
+{
+	unsigned long *mem = (unsigned long *) 0;
+	const unsigned long kend = (1024 / sizeof(unsigned long));
+	unsigned long k, n;
+
+	mtmsr(0);
+
+	for (k = 0; k < CFG_KBYTES_SDRAM;
+	     ++k, mem += (1024 / sizeof(unsigned long))) {
+		if ((k & 1023) == 0) {
+			printf("%3d MB\r", k / 1024);
+		}
+
+		memset(mem, 0xaaaaaaaa, 1024);
+		for (n = 0; n < kend; ++n) {
+			if (mem[n] != 0xaaaaaaaa) {
+				printf("SDRAM test fails at: %08x\n",
+				       (uint) & mem[n]);
+				return 1;
+			}
+		}
+
+		memset(mem, 0x55555555, 1024);
+		for (n = 0; n < kend; ++n) {
+			if (mem[n] != 0x55555555) {
+				printf("SDRAM test fails at: %08x\n",
+				       (uint) & mem[n]);
+				return 1;
+			}
+		}
+	}
+	printf("SDRAM test passes\n");
+
+	return  0;
+}
+#endif
+
+
+/*************************************************************************
+ *  pci_pre_init
+ *
+ *  This routine is called just prior to registering the hose and gives
+ *  the board the opportunity to check things. Returning a value of zero
+ *  indicates that things are bad & PCI initialization should be aborted.
+ *
+ *	Different boards may wish to customize the pci controller structure
+ *	(add regions, override default access routines, etc) or perform
+ *	certain pre-initialization actions.
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
+int pci_pre_init( struct pci_controller *hose )
+{
+	unsigned long strap;
+
+	/*--------------------------------------------------------------------------+
+	 *	The luan board is always configured as the host & requires the
+	 *	PCI arbiter to be enabled.
+	 *--------------------------------------------------------------------------*/
+	mfsdr(sdr_sdstp1, strap);
+	if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ) {
+		printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
+
+		return  0;
+	}
+
+	return  1;
+}
+#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
+
+
+/*************************************************************************
+ *  pci_target_init
+ *
+ *	The bootstrap configuration provides default settings for the pci
+ *	inbound map (PIM). But the bootstrap config choices are limited and
+ *	may not be sufficient for a given board.
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
+void pci_target_init(struct pci_controller *hose)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	/*--------------------------------------------------------------------------+
+	 * Disable everything
+	 *--------------------------------------------------------------------------*/
+	out32r( PCIX0_PIM0SA, 0 ); /* disable */
+	out32r( PCIX0_PIM1SA, 0 ); /* disable */
+	out32r( PCIX0_PIM2SA, 0 ); /* disable */
+	out32r( PCIX0_EROMBA, 0 ); /* disable expansion rom */
+
+	/*--------------------------------------------------------------------------+
+	 * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
+	 * options to not support sizes such as 128/256 MB.
+	 *--------------------------------------------------------------------------*/
+	out32r( PCIX0_PIM0LAL, CFG_SDRAM_BASE );
+	out32r( PCIX0_PIM0LAH, 0 );
+	out32r( PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1 );
+
+	out32r( PCIX0_BAR0, 0 );
+
+	/*--------------------------------------------------------------------------+
+	 * Program the board's subsystem id/vendor id
+	 *--------------------------------------------------------------------------*/
+	out16r( PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID );
+	out16r( PCIX0_SBSYSID, CFG_PCI_SUBSYS_DEVICEID );
+
+	out16r( PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY );
+}
+#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */
+
+
+/*************************************************************************
+ *  is_pci_host
+ *
+ *	This routine is called to determine if a pci scan should be
+ *	performed. With various hardware environments (especially cPCI and
+ *	PPMC) it's insufficient to depend on the state of the arbiter enable
+ *	bit in the strap register, or generic host/adapter assumptions.
+ *
+ *	Rather than hard-code a bad assumption in the general 440 code, the
+ *	440 pci code requires the board to decide at runtime.
+ *
+ *	Return 0 for adapter mode, non-zero for host (monarch) mode.
+ *
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI)
+int is_pci_host(struct pci_controller *hose)
+{
+	return  1;
+}
+#endif				/* defined(CONFIG_PCI) */
+
+
+/*************************************************************************
+ *  hw_watchdog_reset
+ *
+ *	This routine is called to reset (keep alive) the watchdog timer
+ *
+ ************************************************************************/
+#if defined(CONFIG_HW_WATCHDOG)
+void hw_watchdog_reset(void)
+{
+}
+#endif
+
+
+/*************************************************************************
+ *  int on_off()
+ *
+ ************************************************************************/
+static int on_off( const char *s )
+{
+	if (strcmp(s, "on") == 0) {
+		return  1;
+	} else if (strcmp(s, "off") == 0) {
+		return  0;
+	}
+	return  -1;
+}
+
+
+/*************************************************************************
+ *  void l2cache_disable()
+ *
+ ************************************************************************/
+static void l2cache_disable(void)
+{
+	mtdcr( l2_cache_cfg, 0 );
+}
+
+
+/*************************************************************************
+ *  void l2cache_enable()
+ *
+ ************************************************************************/
+static void l2cache_enable(void)	/* see p258 7.4.1 Enabling L2 Cache */
+{
+	mtdcr( l2_cache_cfg, 0x80000000 );	/* enable L2_MODE L2_CFG[L2M] */
+
+	mtdcr( l2_cache_addr, 0 );		/* set L2_ADDR with all zeros */
+
+	mtdcr( l2_cache_cmd, 0x80000000 );	/* issue HCLEAR command via L2_CMD */
+
+	while (!(mfdcr( l2_cache_stat ) & 0x80000000 ))  ;; /* poll L2_SR for completion */
+
+	mtdcr( l2_cache_cmd, 0x10000000 );	/* clear cache errors L2_CMD[CCP] */
+
+	mtdcr( l2_cache_cmd, 0x08000000 );	/* clear tag errors L2_CMD[CTE] */
+
+	mtdcr( l2_cache_snp0, 0 );		/* snoop registers */
+	mtdcr( l2_cache_snp1, 0 );
+
+	__asm__ volatile ("sync");		/* msync */
+
+	mtdcr( l2_cache_cfg, 0xe0000000 );	/* inst and data use L2 */
+
+	__asm__ volatile ("sync");
+}
+
+
+/*************************************************************************
+ *  int l2cache_status()
+ *
+ ************************************************************************/
+static int l2cache_status(void)
+{
+	return  (mfdcr( l2_cache_cfg ) & 0x60000000) != 0;
+}
+
+
+/*************************************************************************
+ *  int do_l2cache()
+ *
+ ************************************************************************/
+int do_l2cache( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[] )
+{
+	switch (argc) {
+	case 2:			/* on / off	*/
+		switch (on_off(argv[1])) {
+		case 0:	l2cache_disable();
+			break;
+		case 1:	l2cache_enable();
+			break;
+		}
+		/* FALL TROUGH */
+	case 1:			/* get status */
+		printf ("L2 Cache is %s\n",
+			l2cache_status() ? "ON" : "OFF");
+		return 0;
+	default:
+		printf ("Usage:\n%s\n", cmdtp->usage);
+		return 1;
+	}
+
+	return  0;
+}
+
+
+U_BOOT_CMD(
+	l2cache,   2,   1,     do_l2cache,
+	"l2cache  - enable or disable L2 cache\n",
+	"[on, off]\n"
+	"    - enable or disable L2 cache\n"
+	);
diff --git a/board/amcc/luan/u-boot.lds b/board/amcc/luan/u-boot.lds
new file mode 100644
index 0000000..24a0fde
--- /dev/null
+++ b/board/amcc/luan/u-boot.lds
@@ -0,0 +1,156 @@
+/*
+ * (C) Copyright 2002
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  .bootpg 0xFFFFF000 :
+  {
+    cpu/ppc4xx/start.o	(.bootpg)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    cpu/ppc4xx/start.o	(.text)
+    board/amcc/luan/init.o	(.text)
+    cpu/ppc4xx/kgdb.o	(.text)
+    cpu/ppc4xx/traps.o	(.text)
+    cpu/ppc4xx/interrupts.o	(.text)
+    cpu/ppc4xx/serial.o	(.text)
+    cpu/ppc4xx/cpu_init.o	(.text)
+    cpu/ppc4xx/speed.o	(.text)
+    common/dlmalloc.o	(.text)
+    lib_generic/crc32.o		(.text)
+    lib_ppc/extable.o	(.text)
+    lib_generic/zlib.o		(.text)
+
+/*    . = env_offset;*/
+/*    common/environment.o(.text)*/
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  . = .;
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  . = .;
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}
diff --git a/cpu/ppc4xx/405gp_pci.c b/cpu/ppc4xx/405gp_pci.c
index 6a4128c..64431ab 100644
--- a/cpu/ppc4xx/405gp_pci.c
+++ b/cpu/ppc4xx/405gp_pci.c
@@ -437,11 +437,11 @@
 	 * The PCI initialization sequence enable bit must be set ... if not abort
 	 * pci setup since updating the bit requires chip reset.
 	 *--------------------------------------------------------------------------*/
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
 	unsigned long strap;
 
 	mfsdr(sdr_sdstp1,strap);
-	if ( (strap & 0x00010000) == 0 ){
+	if ((strap & SDR0_SDSTP1_PISE_MASK) == 0) {
 		printf("PCI: SDR0_STRP1[PISE] not set.\n");
 		printf("PCI: Configuration aborted.\n");
 		return;
@@ -450,7 +450,7 @@
 	unsigned long strap;
 
 	strap = mfdcr(cpc0_strp1);
-	if( (strap & 0x00040000) == 0 ){
+	if ((strap & CPC0_STRP1_PISE_MASK) == 0) {
 		printf("PCI: CPC0_STRP1[PISE] not set.\n");
 		printf("PCI: Configuration aborted.\n");
 		return;
@@ -466,26 +466,26 @@
 
 	pci_set_region(hose->regions + reg_num++,
 		       0x00000000,
-			   PCIX0_IOBASE,
-			   0x10000,
-			   PCI_REGION_IO);
+		       PCIX0_IOBASE,
+		       0x10000,
+		       PCI_REGION_IO);
 
 	pci_set_region(hose->regions + reg_num++,
 		       CFG_PCI_TARGBASE,
-			   CFG_PCI_MEMBASE,
-			   0x10000000,
-			   PCI_REGION_MEM );
+		       CFG_PCI_MEMBASE,
+		       0x10000000,
+		       PCI_REGION_MEM );
 	hose->region_count = reg_num;
 
 	pci_setup_indirect(hose, PCIX0_CFGADR, PCIX0_CFGDATA);
 
 #if defined(CFG_PCI_PRE_INIT)
-    /* Let board change/modify hose & do initial checks */
-    if( pci_pre_init (hose) == 0 ){
-	printf("PCI: Board-specific initialization failed.\n");
-	printf("PCI: Configuration aborted.\n");
-	return;
-    }
+	/* Let board change/modify hose & do initial checks */
+	if (pci_pre_init (hose) == 0) {
+		printf("PCI: Board-specific initialization failed.\n");
+		printf("PCI: Configuration aborted.\n");
+		return;
+	}
 #endif
 
 	pci_register_hose( hose );
@@ -496,9 +496,9 @@
 #if defined(CFG_PCI_TARGET_INIT)
 	pci_target_init(hose);                /* Let board setup pci target */
 #else
-    out16r( PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID );
-    out16r( PCIX0_SBSYSID, CFG_PCI_SUBSYS_ID );
-    out16r( PCIX0_CLS, 0x00060000 ); /* Bridge, host bridge */
+	out16r( PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID );
+	out16r( PCIX0_SBSYSID, CFG_PCI_SUBSYS_ID );
+	out16r( PCIX0_CLS, 0x00060000 ); /* Bridge, host bridge */
 #endif
 
 #if defined(CONFIG_440GX)
@@ -524,24 +524,24 @@
 	out32r( PCIX0_POM0PCIAL, CFG_PCI_MEMBASE );
 	out32r( PCIX0_POM0PCIAH, 0x00000000 );
 	out32r( PCIX0_POM0SA, 0xf0000001 ); /* 256MB, enabled */
-    out32r( PCIX0_STS, in32r( PCIX0_STS ) & ~0x0000fff8 );
+	out32r( PCIX0_STS, in32r( PCIX0_STS ) & ~0x0000fff8 );
 #endif
 
 	/*--------------------------------------------------------------------------+
 	 * PCI host configuration -- we don't make any assumptions here ... the
-     * _board_must_indicate_ what to do -- there's just too many runtime
-     * scenarios in environments like cPCI, PPMC, etc. to make a determination
-     * based on hard-coded values or state of arbiter enable.
+	 * _board_must_indicate_ what to do -- there's just too many runtime
+	 * scenarios in environments like cPCI, PPMC, etc. to make a determination
+	 * based on hard-coded values or state of arbiter enable.
 	 *--------------------------------------------------------------------------*/
-    if( is_pci_host(hose) ){
+	if (is_pci_host(hose)) {
 #ifdef CONFIG_PCI_SCAN_SHOW
-	printf("PCI:   Bus Dev VenId DevId Class Int\n");
+		printf("PCI:   Bus Dev VenId DevId Class Int\n");
 #endif
 #if !defined(CONFIG_440EP) && !defined(CONFIG_440GR)
-	out16r( PCIX0_CMD, in16r( PCIX0_CMD ) | PCI_COMMAND_MASTER);
+		out16r( PCIX0_CMD, in16r( PCIX0_CMD ) | PCI_COMMAND_MASTER);
 #endif
-	hose->last_busno = pci_hose_scan(hose);
-    }
+		hose->last_busno = pci_hose_scan(hose);
+	}
 }
 
 
diff --git a/cpu/ppc4xx/4xx_enet.c b/cpu/ppc4xx/4xx_enet.c
index 8423cc3..86dc2d0 100644
--- a/cpu/ppc4xx/4xx_enet.c
+++ b/cpu/ppc4xx/4xx_enet.c
@@ -314,9 +314,11 @@
 	unsigned mode_reg;
 	unsigned short devnum;
 	unsigned short reg_short;
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
 	sys_info_t sysinfo;
-	int ethgroup;
+#if defined(CONFIG_440GX)
+	int ethgroup = -1;
+#endif
 #endif
 
 	EMAC_4XX_HW_PST hw_p = dev->priv;
@@ -328,7 +330,7 @@
 		return -1;
 	}
 
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
 	/* Need to get the OPB frequency so we can access the PHY */
 	get_sys_info (&sysinfo);
 #endif
@@ -371,7 +373,7 @@
 	hw_p->tx_i_index = 0;	/* Transmit Interrupt Queue Index */
 	hw_p->tx_u_index = 0;	/* Transmit User Queue Index */
 
-#if defined(CONFIG_440)
+#if defined(CONFIG_440) && !defined(CONFIG_440SP)
 	/* set RMII mode */
 	/* NOTE: 440GX spec states that mode is mutually exclusive */
 	/* NOTE: Therefore, disable all other EMACS, since we handle */
@@ -399,7 +401,7 @@
 #endif
 
 	out32 (ZMII_SSR, ZMII_SSR_SP << ZMII_SSR_V(devnum));
-#endif /* defined(CONFIG_440) */
+#endif /* defined(CONFIG_440) && !defined(CONFIG_440SP) */
 
 	__asm__ volatile ("eieio");
 
@@ -414,7 +416,7 @@
 		failsafe--;
 	}
 
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
 	/* Whack the M1 register */
 	mode_reg = 0x0;
 	mode_reg &= ~0x00000038;
@@ -429,7 +431,7 @@
 		mode_reg |= EMAC_M1_OBCI_GT100;
 
 	out32 (EMAC_M1 + hw_p->hw_addr, mode_reg);
-#endif /*  defined(CONFIG_440GX) */
+#endif /* defined(CONFIG_440GX) || defined(CONFIG_440SP) */
 
 	/* wait for PHY to complete auto negotiation */
 	reg_short = 0;
@@ -466,7 +468,7 @@
 	if (hw_p->first_init == 0) {
 		miiphy_reset (dev->name, reg);
 
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
 #if defined(CONFIG_CIS8201_PHY)
 		/*
 		 * Cicada 8201 PHY needs to have an extended register whacked
@@ -542,7 +544,7 @@
 			(int) speed, (duplex == HALF) ? "HALF" : "FULL");
 	}
 
-#if defined(CONFIG_440)
+#if defined(CONFIG_440) && !defined(CONFIG_440SP)
 #if defined(CONFIG_440EP) || defined(CONFIG_440GR)
 	mfsdr(sdr_mfr, reg);
 	if (speed == 100) {
@@ -570,10 +572,10 @@
 
 		out32 (RGMII_SSR, reg);
 	}
-#endif /* defined(CONFIG_440) */
+#endif /* defined(CONFIG_440) && !defined(CONFIG_440SP) */
 
 	/* set the Mal configuration reg */
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
 	mtdcr (malmcr, MAL_CR_PLBB | MAL_CR_OPBBL | MAL_CR_LEA |
 	       MAL_CR_PLBLT_DEFAULT | MAL_CR_EOPIE | 0x00330000);
 #else
@@ -756,9 +758,16 @@
 	mode_reg |= EMAC_M1_RFS_4K | EMAC_M1_TX_FIFO_2K;
 
 	/* set speed */
-	if (speed == _1000BASET)
+	if (speed == _1000BASET) {
+#if defined(CONFIG_440SP)
+#define SDR0_PFC1_EM_1000	0x00200000
+		unsigned long pfc1;
+		mfsdr (sdr_pfc1, pfc1);
+		pfc1 |= SDR0_PFC1_EM_1000;
+		mtsdr (sdr_pfc1, pfc1);
+#endif
 		mode_reg = mode_reg | EMAC_M1_MF_1000MBPS | EMAC_M1_IST;
-	else if (speed == _100BASET)
+	} else if (speed == _100BASET)
 		mode_reg = mode_reg | EMAC_M1_MF_100MBPS | EMAC_M1_IST;
 	else
 		mode_reg = mode_reg & ~0x00C00000;	/* 10 MBPS */
@@ -883,8 +892,21 @@
 	}
 }
 
+
 #if defined (CONFIG_440)
 
+#if defined(CONFIG_440SP)
+/*
+ * Hack: On 440SP all enet irq sources are located on UIC1
+ * Needs some cleanup. --sr
+ */
+#define UIC0MSR		uic1msr
+#define UIC0SR		uic1sr
+#else
+#define UIC0MSR		uic0msr
+#define UIC0SR		uic0sr
+#endif
+
 int enetInt (struct eth_device *dev)
 {
 	int serviced;
@@ -911,20 +933,17 @@
 
 	hw_p = dev->priv;
 
-
 	/* enter loop that stays in interrupt code until nothing to service */
 	do {
 		serviced = 0;
 
-		my_uic0msr = mfdcr (uic0msr);
+		my_uic0msr = mfdcr (UIC0MSR);
 		my_uic1msr = mfdcr (uic1msr);
 #if defined(CONFIG_440GX)
 		my_uic2msr = mfdcr (uic2msr);
 #endif
 		if (!(my_uic0msr & (UIC_MRE | UIC_MTE))
-		    && !(my_uic1msr &
-			 (UIC_ETH0 | UIC_ETH1 | UIC_MS | UIC_MTDE |
-			  UIC_MRDE))) {
+		    && !(my_uic1msr & (UIC_ETH0 | UIC_ETH1 | UIC_MS | UIC_MTDE | UIC_MRDE))) {
 			/* not for us */
 			return (rc);
 		}
@@ -962,12 +981,13 @@
 			}
 			if ((hw_p->emac_ier & emac_isr)
 			    || (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE))) {
-				mtdcr (uic0sr, UIC_MRE | UIC_MTE);	/* Clear */
+				mtdcr (UIC0SR, UIC_MRE | UIC_MTE);	/* Clear */
 				mtdcr (uic1sr, UIC_ETH0 | UIC_MS | UIC_MTDE | UIC_MRDE);	/* Clear */
 				return (rc);	/* we had errors so get out */
 			}
 		}
 
+#if !defined(CONFIG_440SP)
 		if (hw_p->devnum == 1) {
 			if (UIC_ETH1 & my_uic1msr) {	/* look for EMAC errors */
 				emac_isr = in32 (EMAC_ISR + hw_p->hw_addr);
@@ -979,7 +999,7 @@
 			}
 			if ((hw_p->emac_ier & emac_isr)
 			    || (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE))) {
-				mtdcr (uic0sr, UIC_MRE | UIC_MTE);	/* Clear */
+				mtdcr (UIC0SR, UIC_MRE | UIC_MTE);	/* Clear */
 				mtdcr (uic1sr, UIC_ETH1 | UIC_MS | UIC_MTDE | UIC_MRDE);	/* Clear */
 				return (rc);	/* we had errors so get out */
 			}
@@ -996,7 +1016,7 @@
 			}
 			if ((hw_p->emac_ier & emac_isr)
 			    || (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE))) {
-				mtdcr (uic0sr, UIC_MRE | UIC_MTE);	/* Clear */
+				mtdcr (UIC0SR, UIC_MRE | UIC_MTE);	/* Clear */
 				mtdcr (uic1sr, UIC_MS | UIC_MTDE | UIC_MRDE);	/* Clear */
 				mtdcr (uic2sr, UIC_ETH2);
 				return (rc);	/* we had errors so get out */
@@ -1014,18 +1034,20 @@
 			}
 			if ((hw_p->emac_ier & emac_isr)
 			    || (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE))) {
-				mtdcr (uic0sr, UIC_MRE | UIC_MTE);	/* Clear */
+				mtdcr (UIC0SR, UIC_MRE | UIC_MTE);	/* Clear */
 				mtdcr (uic1sr, UIC_MS | UIC_MTDE | UIC_MRDE);	/* Clear */
 				mtdcr (uic2sr, UIC_ETH3);
 				return (rc);	/* we had errors so get out */
 			}
 		}
 #endif /* CONFIG_440GX */
+#endif /* !CONFIG_440SP */
+
 		/* handle MAX TX EOB interrupt from a tx */
 		if (my_uic0msr & UIC_MTE) {
 			mal_rx_eob = mfdcr (maltxeobisr);
 			mtdcr (maltxeobisr, mal_rx_eob);
-			mtdcr (uic0sr, UIC_MTE);
+			mtdcr (UIC0SR, UIC_MTE);
 		}
 		/* handle MAL RX EOB  interupt from a receive */
 		/* check for EOB on valid channels	      */
@@ -1040,7 +1062,8 @@
 				rc = 0;
 			}
 		}
-		mtdcr (uic0sr, UIC_MRE);	/* Clear */
+
+		mtdcr (UIC0SR, UIC_MRE);	/* Clear */
 		mtdcr (uic1sr, UIC_MS | UIC_MTDE | UIC_MRDE);	/* Clear */
 		switch (hw_p->devnum) {
 		case 0:
@@ -1489,7 +1512,7 @@
 #endif
 #if defined(CONFIG_MII) || (CONFIG_COMMANDS & CFG_CMD_MII)
 		miiphy_register (dev->name,
-				emac4xx_miiphy_read, emac4xx_miiphy_write);
+				 emac4xx_miiphy_read, emac4xx_miiphy_write);
 #endif
 
 	}			/* end for each supported device */
@@ -1531,7 +1554,7 @@
 {
 #if defined(CONFIG_MII) || (CONFIG_COMMANDS & CFG_CMD_MII)
 	miiphy_register ("ppc_4xx_eth0",
-			emac4xx_miiphy_read, emac4xx_miiphy_write);
+			 emac4xx_miiphy_read, emac4xx_miiphy_write);
 #endif
 
 	return 0;
diff --git a/cpu/ppc4xx/cpu.c b/cpu/ppc4xx/cpu.c
index 6c61953..0b5883c 100644
--- a/cpu/ppc4xx/cpu.c
+++ b/cpu/ppc4xx/cpu.c
@@ -38,42 +38,75 @@
 #include <ppc4xx.h>
 
 
-#if defined(CONFIG_405GP)
-#define PCI_ARBITER_ENABLED	(mfdcr(strap) & PSR_PCI_ARBIT_EN)
-#define PCI_ASYNC_ENABLED	(mfdcr(strap) & PSR_PCI_ASYNC_EN)
-#endif
-
-#if defined(CONFIG_405EP)
-#define PCI_ARBITER_ENABLED	(mfdcr(cpc0_pci) & CPC0_PCI_ARBIT_EN)
-#define I2C_BOOTROM_ENABLED	(mfdcr(cpc0_boot) & CPC0_BOOT_SEP)
-#endif
-
-#if defined(CONFIG_440EP) || defined(CONFIG_440GR)
-#define SDR0_SDSTP1_PAE		(0x80000000 >> 21)
-#define SDR0_SDSTP1_PAME	(0x80000000 >> 27)
-
-#define PCI_ARBITER_ENABLED	(mfdcr(cpc0_strp1) & SDR0_SDSTP1_PAE)
-#define PCI_ASYNC_ENABLED	(mfdcr(cpc0_strp1) & SDR0_SDSTP1_PAME)
-#endif
-
-#if defined(CONFIG_440GP)
-#define CPC0_STRP1_PAE		(0x80000000 >> 11)
-
-#define PCI_ARBITER_ENABLED	(mfdcr(cpc0_strp1) & CPC0_STRP1_PAE)
-#endif
-
-#if defined(CONFIG_440GX)
-#define SDR0_SDSTP1_PAE		(0x80000000 >> 13)
-
-#define PCI_ARBITER_ENABLED	(mfdcr(cpc0_strp1) & SDR0_SDSTP1_PAE)
-#endif
-
 #if defined(CONFIG_440)
 #define FREQ_EBC		(sys_info.freqEPB)
 #else
 #define FREQ_EBC		(sys_info.freqPLB / sys_info.pllExtBusDiv)
 #endif
 
+#if defined(CONFIG_405GP) || defined(CONFIG_440EP) || defined(CONFIG_440GR)
+
+#define PCI_ASYNC
+
+int pci_async_enabled(void)
+{
+#if defined(CONFIG_405GP)
+	return (mfdcr(strap) & PSR_PCI_ASYNC_EN);
+#endif
+
+#if defined(CONFIG_440EP) || defined(CONFIG_440GR)
+	unsigned long val;
+
+	mfsdr(cpc0_strp1, val);
+	return (val & SDR0_SDSTP1_PAME_MASK);
+#endif
+}
+#endif
+
+#if defined(CONFIG_PCI)
+int pci_arbiter_enabled(void)
+{
+#if defined(CONFIG_405GP)
+	return (mfdcr(strap) & PSR_PCI_ARBIT_EN);
+#endif
+
+#if defined(CONFIG_405EP)
+	return (mfdcr(cpc0_pci) & CPC0_PCI_ARBIT_EN);
+#endif
+
+#if defined(CONFIG_440GP)
+	return (mfdcr(cpc0_strp1) & CPC0_STRP1_PAE_MASK);
+#endif
+
+#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP)
+	unsigned long val;
+
+	mfsdr(sdr_sdstp1, val);
+	return (val & SDR0_SDSTP1_PAE_MASK);
+#endif
+}
+#endif
+
+#if defined(CONFIG_405EP)|| defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
+	defined(CONFIG_440GX) || defined(CONFIG_440SP)
+
+#define I2C_BOOTROM
+
+int i2c_bootrom_enabled(void)
+{
+#if defined(CONFIG_405EP)
+	return (mfdcr(cpc0_boot) & CPC0_BOOT_SEP);
+#endif
+
+#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP)
+	unsigned long val;
+
+	mfsdr(sdr_sdcs, val);
+	return (val & SDR0_SDCS_SDD);
+#endif
+}
+#endif
+
 
 #if defined(CONFIG_440)
 static int do_chip_reset(unsigned long sys0, unsigned long sys1);
@@ -196,6 +229,14 @@
 #endif /* CONFIG_440GR */
 #endif /* CONFIG_440 */
 
+	case PVR_440SP_RA:
+		puts("SP Rev. A");
+		break;
+
+	case PVR_440SP_RB:
+		puts("SP Rev. B");
+		break;
+
 	default:
 		printf (" UNKNOWN (PVR=%08x)", pvr);
 		break;
@@ -206,17 +247,16 @@
 	       sys_info.freqPLB / sys_info.pllOpbDiv / 1000000,
 	       FREQ_EBC / 1000000);
 
-#if defined(I2C_BOOTROM_ENABLED)
-	printf ("       IIC Boot EEPROM %sabled\n", I2C_BOOTROM_ENABLED ? "en" : "dis");
+#if defined(I2C_BOOTROM)
+	printf ("       I2C boot EEPROM %sabled\n", i2c_bootrom_enabled() ? "en" : "dis");
 #endif
 
-#if defined(PCI_ARBITER_ENABLED)
-	printf ("       %sternal PCI arbiter enabled",
-		(PCI_ARBITER_ENABLED) ? "In" : "Ex");
+#if defined(CONFIG_PCI)
+	printf ("       Internal PCI arbiter %sabled", pci_arbiter_enabled() ? "en" : "dis");
 #endif
 
-#if defined(PCI_ASYNC_ENABLED)
-	if (PCI_ASYNC_ENABLED) {
+#if defined(PCI_ASYNC)
+	if (pci_async_enabled()) {
 		printf (", PCI async ext clock used");
 	} else {
 		printf (", PCI sync clock at %lu MHz",
@@ -224,7 +264,7 @@
 	}
 #endif
 
-#if defined(PCI_ARBITER_ENABLED) || defined(PCI_ASYNC_ENABLED)
+#if defined(CONFIG_PCI)
 	putc('\n');
 #endif
 
diff --git a/cpu/ppc4xx/miiphy.c b/cpu/ppc4xx/miiphy.c
index f319eb8..f26f2a2 100644
--- a/cpu/ppc4xx/miiphy.c
+++ b/cpu/ppc4xx/miiphy.c
@@ -104,7 +104,7 @@
 /***********************************************************/
 unsigned int miiphy_getemac_offset (void)
 {
-#if defined(CONFIG_440) && defined(CONFIG_NET_MULTI)
+#if (defined(CONFIG_440) && !defined(CONFIG_440SP)) && defined(CONFIG_NET_MULTI)
 	unsigned long zmii;
 	unsigned long eoffset;
 
diff --git a/cpu/ppc4xx/serial.c b/cpu/ppc4xx/serial.c
index e06fb0d..e7f6bcb 100644
--- a/cpu/ppc4xx/serial.c
+++ b/cpu/ppc4xx/serial.c
@@ -276,7 +276,12 @@
 #define UART0_BASE  CFG_PERIPHERAL_BASE + 0x00000200
 #define UART1_BASE  CFG_PERIPHERAL_BASE + 0x00000300
 #endif
-#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR)
+
+#if defined(CONFIG_440SP)
+#define UART2_BASE  CFG_PERIPHERAL_BASE + 0x00000600
+#endif
+
+#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP)
 #define CR0_MASK        0xdfffffff
 #define CR0_EXTCLK_ENA  0x00800000
 #define CR0_UDIV_POS    0
@@ -306,14 +311,14 @@
 #if defined(CONFIG_UART1_CONSOLE)
 #define ACTING_UART0_BASE	UART1_BASE
 #define ACTING_UART1_BASE	UART0_BASE
-#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR)
+#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP)
 #define UART0_SDR           sdr_uart1
 #define UART1_SDR           sdr_uart0
 #endif /* CONFIG_440GX */
 #else
 #define ACTING_UART0_BASE	UART0_BASE
 #define ACTING_UART1_BASE	UART1_BASE
-#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR)
+#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP)
 #define UART0_SDR           sdr_uart0
 #define UART1_SDR           sdr_uart1
 #endif /* CONFIG_440GX */
@@ -436,7 +441,7 @@
 	unsigned long tmp;
 #endif
 
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
 #if defined(CONFIG_SERIAL_MULTI)
 	if (UART0_BASE == dev_base) {
 		mfsdr(UART0_SDR,reg);
@@ -465,7 +470,7 @@
 	serial_divs (gd->baudrate, &udiv, &bdiv);
 #endif
 
-#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR)
+#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP)
 	reg |= udiv << CR0_UDIV_POS;	/* set the UART divisor */
 #if defined(CONFIG_SERIAL_MULTI)
 	if (UART0_BASE == dev_base) {
diff --git a/cpu/ppc4xx/speed.c b/cpu/ppc4xx/speed.c
index cbd7b24..553c491 100644
--- a/cpu/ppc4xx/speed.c
+++ b/cpu/ppc4xx/speed.c
@@ -283,7 +283,7 @@
 	return sys_info.freqPCI;
 }
 
-#elif !defined(CONFIG_440GX)
+#elif !defined(CONFIG_440GX) && !defined(CONFIG_440SP)
 void get_sys_info (sys_info_t * sysInfo)
 {
 	unsigned long strp0;
diff --git a/cpu/ppc4xx/start.S b/cpu/ppc4xx/start.S
index 8f7e817..48b430d 100644
--- a/cpu/ppc4xx/start.S
+++ b/cpu/ppc4xx/start.S
@@ -166,7 +166,7 @@
 	mtspr	srr1,r0
 	mtspr	csrr0,r0
 	mtspr	csrr1,r0
-#if defined (CONFIG_440GX) /* NOTE: 440GX adds machine check status regs */
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP) /* NOTE: 440GX adds machine check status regs */
 	mtspr	mcsrr0,r0
 	mtspr	mcsrr1,r0
 	mfspr	r1, mcsr
@@ -394,7 +394,7 @@
 	addi	r3,r3,32
 	bdnz	..d_ag
 #else
-#if defined (CONFIG_440GX)
+#if defined (CONFIG_440GX) || defined(CONFIG_440SP)
 	mtdcr	l2_cache_cfg,r0		/* Ensure L2 Cache is off */
 #endif
 	mtdcr	isram0_sb1cr,r0		/* Disable bank 1 */
@@ -409,7 +409,7 @@
 	mtdcr	isram0_pmeg,r1
 
 	lis	r1,0x8000		/* BAS = 8000_0000 */
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
 	ori	r1,r1,0x0980		/* first 64k */
 	mtdcr	isram0_sb0cr,r1
 	lis	r1,0x8001
@@ -432,7 +432,6 @@
 	/*----------------------------------------------------------------*/
 	lis	r1,CFG_INIT_RAM_ADDR@h
 	ori	r1,r1,CFG_INIT_SP_OFFSET@l
-
 	li	r0,0
 	stwu	r0,-4(r1)
 	stwu	r0,-4(r1)		/* Terminate call chain */
@@ -977,12 +976,8 @@
 invalidate_dcache:
 	addi	r6,0,0x0000		/* clear GPR 6 */
 	/* Do loop for # of dcache congruence classes. */
-#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR)
 	lis	r7, (CFG_DCACHE_SIZE / CFG_CACHELINE_SIZE / 2)@ha	/* TBS for large sized cache */
 	ori	r7, r7, (CFG_DCACHE_SIZE / CFG_CACHELINE_SIZE / 2)@l
-#else
-	addi	r7,r0, (CFG_DCACHE_SIZE / CFG_CACHELINE_SIZE / 2)
-#endif
 					/* NOTE: dccci invalidates both */
 	mtctr	r7			/* ways in the D cache */
 ..dcloop:
@@ -1003,15 +998,10 @@
 	mtdccr	r10
 
 	/* do loop for # of congruence classes. */
-#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR)
 	lis	r10,(CFG_DCACHE_SIZE / CFG_CACHELINE_SIZE / 2)@ha	/* TBS: for large cache sizes */
 	ori	r10,r10,(CFG_DCACHE_SIZE / CFG_CACHELINE_SIZE / 2)@l
 	lis	r11,(CFG_DCACHE_SIZE / 2)@ha /* D cache set size - 2 way sets */
 	ori	r11,r11,(CFG_DCACHE_SIZE / 2)@l /* D cache set size - 2 way sets */
-#else
-	addi	r10,r0,(CFG_DCACHE_SIZE / CFG_CACHELINE_SIZE / 2)
-	addi	r11,r0,(CFG_DCACHE_SIZE / 2) /* D cache set size - 2 way sets */
-#endif
 	mtctr	r10
 	addi	r10,r0,(0xE000-0x10000) /* start at 0xFFFFE000 */
 	add	r11,r10,r11		/* add to get to other side of cache line */
@@ -1233,9 +1223,9 @@
 #if defined(CONFIG_440EP) || defined(CONFIG_440GR)
 	dccci	0,0			    /* Invalidate data cache, now no longer our stack */
 	sync
-	addi	r1,r0,0x0000	    /* Tlb entry #0 */
+	addi	r1,r0,0x0000		/* TLB entry #0 */
 	tlbre	r0,r1,0x0002		/* Read contents */
-	ori	r0,r0,0x0c00	    /* Or in the inhibit, write through bit */
+	ori	r0,r0,0x0c00		/* Or in the inhibit, write through bit */
 	tlbwe	r0,r1,0x0002		/* Save it out */
 	isync
 #endif
diff --git a/cpu/ppc4xx/vecnum.h b/cpu/ppc4xx/vecnum.h
index 1038975..cbfe41d 100644
--- a/cpu/ppc4xx/vecnum.h
+++ b/cpu/ppc4xx/vecnum.h
@@ -31,7 +31,35 @@
 #ifndef _VECNUMS_H_
 #define _VECNUMS_H_
 
-#if defined(CONFIG_440)
+#if defined(CONFIG_440SP)
+
+/* UIC 0 */
+#define VECNUM_U0           0           /* UART0                        */
+#define VECNUM_U1           1           /* UART1                        */
+#define VECNUM_IIC0         2           /* IIC0                         */
+#define VECNUM_IIC1         3           /* IIC1                         */
+#define VECNUM_PIM          4           /* PCI inbound message          */
+#define VECNUM_PCRW         5           /* PCI command reg write        */
+#define VECNUM_PPM          6           /* PCI power management         */
+#define VECNUM_UIC1NC       30          /* UIC1 non-critical interrupt  */
+#define VECNUM_UIC1C        31          /* UIC1 critical interrupt      */
+
+/* UIC 1 */
+#define VECNUM_EIR0         (32 + 0)	/* External interrupt 0         */
+#define VECNUM_MS           (32 + 1)	/* MAL SERR                     */
+#define VECNUM_TXDE         (32 + 2)	/* MAL TXDE                     */
+#define VECNUM_RXDE         (32 + 3)	/* MAL RXDE                     */
+#define VECNUM_MTE          (32 + 6)	/* MAL Tx EOB                   */
+#define VECNUM_MRE          (32 + 7)	/* MAL Rx EOB                   */
+#define VECNUM_CT0          (32 + 12)	/* GPT compare timer 0          */
+#define VECNUM_CT1          (32 + 13)	/* GPT compare timer 1          */
+#define VECNUM_CT2          (32 + 14)	/* GPT compare timer 2          */
+#define VECNUM_CT3          (32 + 15)	/* GPT compare timer 3          */
+#define VECNUM_CT4          (32 + 16)	/* GPT compare timer 4          */
+#define VECNUM_ETH0         (32 + 28)	/* Ethernet interrupt status    */
+#define VECNUM_EWU0         (32 + 29)	/* Emac  wakeup                 */
+
+#elif defined(CONFIG_440)
 
 /* UIC 0 */
 #define VECNUM_U0           0           /* UART0                        */
diff --git a/include/asm-ppc/processor.h b/include/asm-ppc/processor.h
index 0b30d2d..8113783 100644
--- a/include/asm-ppc/processor.h
+++ b/include/asm-ppc/processor.h
@@ -731,6 +731,8 @@
 #define PVR_440GX_RC	0x51B21892
 #define PVR_440GX_RF	0x51B21894
 #define PVR_405EP_RB	0x51210950
+#define PVR_440SP_RA	0x53221850
+#define PVR_440SP_RB	0x53221891
 #define PVR_601		0x00010000
 #define PVR_602		0x00050000
 #define PVR_603		0x00030000
diff --git a/include/configs/luan.h b/include/configs/luan.h
new file mode 100644
index 0000000..0335a00
--- /dev/null
+++ b/include/configs/luan.h
@@ -0,0 +1,306 @@
+/*
+ * (C) Copyright 2005
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ * John Otken, jotken@softadvances.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/************************************************************************
+ * luan.h - configuration for LUAN board
+ ***********************************************************************/
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_LUAN		1	/* Board is Luan		*/
+#define CONFIG_440SP		1	/* Specific PPC440SP support    */
+#define CONFIG_4xx		1	/* PPC4xx family	        */
+#define CONFIG_440		1
+#define CONFIG_SYS_CLK_FREQ	33333333 /* external freq to pll	*/
+
+#define CONFIG_BOARD_EARLY_INIT_F 1     /* call board_early_init_f()	*/
+#define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
+
+/*-----------------------------------------------------------------------
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ *----------------------------------------------------------------------*/
+#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor */
+#define CFG_MALLOC_LEN		(256 * 1024)	/* Reserve 256 kB for malloc  */
+#define CFG_MONITOR_BASE	(-CFG_MONITOR_LEN)
+#define CFG_SDRAM_BASE	        0x00000000	/* MUST be zero */
+
+#define CFG_LARGE_FLASH		0xffc00000	/* 4MB flash address CS0 */
+#define CFG_SMALL_FLASH		0xff900000	/* 1MB flash address CS2 */
+#define CFG_SRAM_BASE		0xff800000	/* 1MB SRAM  address CS2 */
+#define CFG_EPLD_BASE		0xff000000	/* EPLD and FRAM     CS1 */
+
+#define CFG_ISRAM_BASE	        0xf8000000	/* internal 8k SRAM (L2 cache) */
+
+#define CFG_PERIPHERAL_BASE     0xf0000000	/* internal peripherals */
+
+#define CFG_PCI_MEMBASE		0x80000000	/* mapped pci memory */
+#define CFG_PCI_BASE		0xd0000000	/* internal PCI regs */
+#define CFG_PCI_TARGBASE	0x80000000	/* PCIaddr mapped to CFG_PCI_MEMBASE */
+
+#if CFG_LARGE_FLASH == 0xffc00000
+#define CFG_FLASH_BASE		CFG_LARGE_FLASH
+#else
+#define CFG_FLASH_BASE		CFG_SMALL_FLASH
+#endif
+
+#undef CFG_DRAM_TEST
+#if CFG_SRAM_BASE
+#define CFG_KBYTES_SDRAM	1024*2
+#else
+#define CFG_KBYTES_SDRAM	1024
+#endif
+
+/*-----------------------------------------------------------------------
+ * Initial RAM & stack pointer (placed in SDRAM)
+ *----------------------------------------------------------------------*/
+#define CFG_INIT_RAM_ADDR	CFG_ISRAM_BASE
+#define CFG_INIT_RAM_END	(8 << 10)
+#define CFG_GBL_DATA_SIZE	256		/* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#define CFG_EXT_SERIAL_CLOCK	11059200 /* external 11.059MHz clk */
+#define CONFIG_BAUDRATE		115200
+#undef  CONFIG_SERIAL_MULTI
+#undef  CONFIG_UART1_CONSOLE		/* define if you want console on UART1 */
+
+#define CFG_BAUDRATE_TABLE  \
+    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+/*
+ * Define here the location of the environment variables (FLASH or EEPROM).
+ * Note: DENX encourages to use redundant environment in FLASH.
+ */
+#define CFG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/
+
+/*-----------------------------------------------------------------------
+ * FLASH related
+ *----------------------------------------------------------------------*/
+#define CFG_MAX_FLASH_BANKS	3	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	64	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
+
+#define CFG_FLASH_ADDR0         0x555
+#define CFG_FLASH_ADDR1         0x2aa
+#define CFG_FLASH_WORD_SIZE     unsigned char
+
+#ifdef CFG_ENV_IS_IN_FLASH
+#define CFG_ENV_SECT_SIZE	0x10000 /* size of one complete sector	*/
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE		0x2000	/* Total Size of Environment Sector	*/
+
+/* Address and size of Redundant Environment Sector	*/
+#define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+#endif /* CFG_ENV_IS_IN_FLASH */
+
+/*-----------------------------------------------------------------------
+ * DDR SDRAM
+ *----------------------------------------------------------------------*/
+#undef  CONFIG_SPD_EEPROM		/* SPD EEPROM init doesn't support DDR2 */
+#define SPD_EEPROM_ADDRESS {0x52,0x53}	/* I2C SPD addresses */
+#define IIC0_DIMM0_ADDR         0x52
+#define IIC0_DIMM1_ADDR         0x53
+
+/*-----------------------------------------------------------------------
+ * I2C
+ *----------------------------------------------------------------------*/
+#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
+#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CFG_I2C_SLAVE		0x7F
+
+#define CONFIG_PREBOOT	"echo;"	\
+	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+	"echo"
+
+#undef	CONFIG_BOOTARGS
+
+#define CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"							\
+	"hostname=luan\0"						\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=$(serverip):$(rootpath)\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs $(bootargs) "				\
+		"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)"	\
+		":$(hostname):$(netdev):off panic=1\0"			\
+	"addtty=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)\0"\
+	"flash_nfs=run nfsargs addip addtty;"				\
+		"bootm $(kernel_addr)\0"				\
+	"flash_self=run ramargs addip addtty;"				\
+		"bootm $(kernel_addr) $(ramdisk_addr)\0"		\
+	"net_nfs=tftp 200000 $(bootfile);run nfsargs addip addtty;"     \
+	        "bootm\0"						\
+	"rootpath=/opt/eldk/ppc_4xx\0"					\
+	"bootfile=/tftpboot/luan/uImage\0"				\
+	"kernel_addr=fc000000\0"					\
+	"ramdisk_addr=fc100000\0"					\
+	"load=tftp 100000 /tftpboot/luan/u-boot.bin\0"			\
+	"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;"	\
+		"cp.b 100000 fffc0000 40000;"			        \
+		"setenv filesize;saveenv\0"				\
+	"upd=run load;run update\0"					\
+	""
+#define CONFIG_BOOTCOMMAND	"run flash_self"
+
+#if 0
+#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
+#else
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
+#endif
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+
+#define CONFIG_MII		1	/* MII PHY management		*/
+#define CONFIG_PHY_ADDR		1
+#define CONFIG_CIS8201_PHY	1	/* Enable 'special' RGMII mode for Cicada phy */
+#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
+
+#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
+
+#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
+#define CONFIG_NET_MULTI		/* needed for NetConsole	*/
+
+/* Partitions */
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+
+#ifdef DEBUG
+#define CONFIG_PANIC_HANG
+#else
+#define CONFIG_HW_WATCHDOG			/* watchdog */
+#endif
+
+#define CONFIG_COMMANDS	       (CONFIG_CMD_DFL		|	\
+				CFG_CMD_ASKENV		|	\
+			        CFG_CMD_CACHE		|	\
+				CFG_CMD_DHCP		|	\
+				CFG_CMD_DIAG		|	\
+				CFG_CMD_ELF		|	\
+				CFG_CMD_I2C		|	\
+				CFG_CMD_IRQ		|	\
+				CFG_CMD_MII		|	\
+				CFG_CMD_NET		|	\
+				CFG_CMD_NFS		|	\
+				CFG_CMD_PCI		|	\
+				CFG_CMD_PING		|	\
+				CFG_CMD_REGINFO		|	\
+				CFG_CMD_SETGETDCR	|	\
+				CFG_CMD_SDRAM		|	\
+				0)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	        16	/* max number of command args	*/
+#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000 /* memtest works on	        */
+#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
+
+#define CFG_LOAD_ADDR		0x100000 /* default load address */
+#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
+#undef  CONFIG_LYNXKDI			/* support kdi files            */
+
+#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#if (CONFIG_COMMANDS & CFG_CMD_PCI)
+
+/* General PCI */
+#define CONFIG_PCI			/* include pci support	        */
+#define CONFIG_PCI_PNP			/* do (not) pci plug-and-play   */
+#define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup  */
+
+/* Board-specific PCI */
+#define CFG_PCI_PRE_INIT                /* enable board pci_pre_init()  */
+#define CFG_PCI_TARGET_INIT
+#undef  CFG_PCI_MASTER_INIT
+
+#define CFG_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC */
+#define CFG_PCI_SUBSYS_DEVICEID 0x4403	/* whatever */
+
+#endif /* CONFIG_COMMANDS & CFG_CMD_PCI */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE		(32<<10) /* For AMCC 440 CPUs			*/
+#define CFG_CACHELINE_SIZE	32	/* ...			*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+#endif	/* __CONFIG_H */
diff --git a/include/ppc440.h b/include/ppc440.h
index 41db16f..018f7be 100644
--- a/include/ppc440.h
+++ b/include/ppc440.h
@@ -78,7 +78,7 @@
 #define	 ivor13 0x19d	/* interrupt vector offset register 13 */
 #define	 ivor14 0x19e	/* interrupt vector offset register 14 */
 #define	 ivor15 0x19f	/* interrupt vector offset register 15 */
-#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR)
+#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP)
 #define	 mcsrr0 0x23a	/* machine check save/restore register 0 */
 #define	 mcsrr1 0x23b	/* mahcine check save/restore register 1 */
 #define	 mcsr	0x23c	/* machine check status register */
@@ -178,7 +178,6 @@
 #define sdr_plbtr	0x4200
 #define sdr_mfr		0x4300	/* SDR0_MFR reg */
 
-
 /*-----------------------------------------------------------------------------
  | SDRAM Controller
  +----------------------------------------------------------------------------*/
@@ -504,7 +503,7 @@
 /*-----------------------------------------------------------------------------
  | L2 Cache
  +----------------------------------------------------------------------------*/
-#if defined (CONFIG_440GX)
+#if defined (CONFIG_440GX) || defined(CONFIG_440SP)
 #define L2_CACHE_BASE	0x030
 #define l2_cache_cfg	(L2_CACHE_BASE+0x00)	/* L2 Cache Config	*/
 #define l2_cache_cmd	(L2_CACHE_BASE+0x01)	/* L2 Cache Command	*/
@@ -527,7 +526,7 @@
  | Clocking, Power Management and Chip Control
  +----------------------------------------------------------------------------*/
 #define CNTRL_DCR_BASE 0x0b0
-#if defined (CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
 #define cpc0_er		(CNTRL_DCR_BASE+0x00)	/* CPM enable register		*/
 #define cpc0_fr		(CNTRL_DCR_BASE+0x01)	/* CPM force register		*/
 #define cpc0_sr		(CNTRL_DCR_BASE+0x02)	/* CPM status register		*/
@@ -690,6 +689,40 @@
 /*---------------------------------------------------------------------------+
 |  Universal interrupt controller 0 interrupts (UIC0)
 +---------------------------------------------------------------------------*/
+#if defined(CONFIG_440SP)
+#define UIC_U0		0x80000000	/* UART 0			    */
+#define UIC_U1		0x40000000	/* UART 1			    */
+#define UIC_IIC0	0x20000000	/* IIC				    */
+#define UIC_IIC1	0x10000000	/* IIC				    */
+#define UIC_PIM		0x08000000	/* PCI0 inbound message		    */
+#define UIC_PCRW	0x04000000	/* PCI0 command write register	    */
+#define UIC_PPM		0x02000000	/* PCI0 power management	    */
+#define UIC_PVPD	0x01000000	/* PCI0 VPD Access		    */
+#define UIC_MSI0	0x00800000	/* PCI0 MSI level 0		    */
+#define UIC_P1IM	0x00400000	/* PCI1 Inbound Message		    */
+#define UIC_P1CRW	0x00200000	/* PCI1 command write register	    */
+#define UIC_P1PM	0x00100000	/* PCI1 power management	    */
+#define UIC_P1VPD	0x00080000	/* PCI1 VPD Access		    */
+#define UIC_P1MSI0	0x00040000	/* PCI1 MSI level 0		    */
+#define UIC_P2IM	0x00020000	/* PCI2 inbound message		    */
+#define UIC_P2CRW	0x00010000	/* PCI2 command register write	    */
+#define UIC_P2PM	0x00008000	/* PCI2 power management	    */
+#define UIC_P2VPD	0x00004000	/* PCI2 VPD access		    */
+#define UIC_P2MSI0	0x00002000	/* PCI2 MSI level 0		    */
+#define UIC_D0CPF	0x00001000	/* DMA0 command pointer		    */
+#define UIC_D0CSF	0x00000800	/* DMA0 command status		    */
+#define UIC_D1CPF	0x00000400	/* DMA1 command pointer		    */
+#define UIC_D1CSF	0x00000200	/* DMA1 command status		    */
+#define UIC_I2OID	0x00000100	/* I2O inbound doorbell		    */
+#define UIC_I2OPLF	0x00000080	/* I2O inbound post list	    */
+#define UIC_I2O0LL	0x00000040	/* I2O0 low latency PLB write	    */
+#define UIC_I2O1LL	0x00000020	/* I2O1 low latency PLB write	    */
+#define UIC_I2O0HB	0x00000010	/* I2O0 high bandwidth PLB write    */
+#define UIC_I2O1HB	0x00000008	/* I2O1 high bandwidth PLB write    */
+#define UIC_GPTCT	0x00000004	/* GPT count timer		    */
+#define UIC_UIC1NC	0x00000002	/* UIC1 non-critical interrupt	    */
+#define UIC_UIC1C	0x00000001	/* UIC1 critical interrupt	    */
+#else  /* CONFIG_440SP */
 #define UIC_U0		0x80000000	/* UART 0			    */
 #define UIC_U1		0x40000000	/* UART 1			    */
 #define UIC_IIC0	0x20000000	/* IIC				    */
@@ -722,6 +755,7 @@
 #define UIC_EIR6	0x00000004	/* External interrupt 6		    */
 #define UIC_UIC1NC	0x00000002	/* UIC1 non-critical interrupt	    */
 #define UIC_UIC1C	0x00000001	/* UIC1 critical interrupt	    */
+#endif /* CONFIG_440SP */
 
 /* For compatibility with 405 code */
 #define UIC_MAL_TXEOB	UIC_MTE
@@ -730,6 +764,40 @@
 /*---------------------------------------------------------------------------+
 |  Universal interrupt controller 1 interrupts (UIC1)
 +---------------------------------------------------------------------------*/
+#if defined(CONFIG_440SP)
+#define UIC_EIR0	0x80000000	/* External interrupt 0		    */
+#define UIC_MS		0x40000000	/* MAL SERR			    */
+#define UIC_MTDE	0x20000000	/* MAL TXDE			    */
+#define UIC_MRDE	0x10000000	/* MAL RXDE			    */
+#define UIC_DECE	0x08000000	/* DDR SDRAM correctible error	    */
+#define UIC_EBCO	0x04000000	/* EBCO interrupt status	    */
+#define UIC_MTE		0x02000000	/* MAL TXEOB			    */
+#define UIC_MRE		0x01000000	/* MAL RXEOB			    */
+#define UIC_P0MSI1	0x00800000	/* PCI0 MSI level 1		    */
+#define UIC_P1MSI1	0x00400000	/* PCI1 MSI level 1		    */
+#define UIC_P2MSI1	0x00200000	/* PCI2 MSI level 1		    */
+#define UIC_L2C		0x00100000	/* L2 cache			    */
+#define UIC_CT0		0x00080000	/* GPT compare timer 0		    */
+#define UIC_CT1		0x00040000	/* GPT compare timer 1		    */
+#define UIC_CT2		0x00020000	/* GPT compare timer 2		    */
+#define UIC_CT3		0x00010000	/* GPT compare timer 3		    */
+#define UIC_CT4		0x00008000	/* GPT compare timer 4		    */
+#define UIC_EIR1	0x00004000	/* External interrupt 1		    */
+#define UIC_EIR2	0x00002000	/* External interrupt 2		    */
+#define UIC_EIR3	0x00001000	/* External interrupt 3		    */
+#define UIC_EIR4	0x00000800	/* External interrupt 4		    */
+#define UIC_EIR5	0x00000400	/* External interrupt 5		    */
+#define UIC_DMAE	0x00000200	/* DMA error			    */
+#define UIC_I2OE	0x00000100	/* I2O error			    */
+#define UIC_SRE		0x00000080	/* Serial ROM error		    */
+#define UIC_P0AE	0x00000040	/* PCI0 asynchronous error	    */
+#define UIC_P1AE	0x00000020	/* PCI1 asynchronous error	    */
+#define UIC_P2AE	0x00000010	/* PCI2 asynchronous error	    */
+#define UIC_ETH0	0x00000008	/* Ethernet 0			    */
+#define UIC_EWU0	0x00000004	/* Ethernet 0 wakeup		    */
+#define UIC_ETH1	0x00000002	/* Reserved			    */
+#define UIC_XOR		0x00000001	/* XOR				    */
+#else /* CONFIG_440SP */
 #define UIC_MS		0x80000000	/* MAL SERR			    */
 #define UIC_MTDE	0x40000000	/* MAL TXDE			    */
 #define UIC_MRDE	0x20000000	/* MAL RXDE			    */
@@ -762,6 +830,7 @@
 #define UIC_EWU0	0x00000004	/* Ethernet 0 wakeup		    */
 #define UIC_ETH1	0x00000002	/* Ethernet 1			    */
 #define UIC_EWU1	0x00000001	/* Ethernet 1 wakeup		    */
+#endif /* CONFIG_440SP */
 
 /* For compatibility with 405 code */
 #define UIC_MAL_SERR	UIC_MS
@@ -850,6 +919,11 @@
 #define EBC_BXAP_TWT_ENCODE(n)		((((unsigned long)(n))&0xFF)<<23)
 #define EBC_BXAP_BCE_DISABLE		0x00000000
 #define EBC_BXAP_BCE_ENABLE		0x00400000
+#define EBC_BXAP_BCT_MASK		0x00300000
+#define EBC_BXAP_BCT_2TRANS		0x00000000
+#define EBC_BXAP_BCT_4TRANS		0x00100000
+#define EBC_BXAP_BCT_8TRANS		0x00200000
+#define EBC_BXAP_BCT_16TRANS		0x00300000
 #define EBC_BXAP_CSN_ENCODE(n)		((((unsigned long)(n))&0x3)<<18)
 #define EBC_BXAP_OEN_ENCODE(n)		((((unsigned long)(n))&0x3)<<16)
 #define EBC_BXAP_WBN_ENCODE(n)		((((unsigned long)(n))&0x3)<<14)
@@ -905,133 +979,22 @@
 #define EBC_CFG_PR_128			0x0000C000
 
 /*-----------------------------------------------------------------------------+
-|  SDR 0 Bit Settings
+|  SDR0 Bit Settings
 +-----------------------------------------------------------------------------*/
-#define SDR0_SDSTP0_ENG_MASK		0x80000000
-#define SDR0_SDSTP0_ENG_PLLDIS		0x00000000
-#define SDR0_SDSTP0_ENG_PLLENAB		0x80000000
-#define SDR0_SDSTP0_ENG_ENCODE(n)	((((unsigned long)(n))&0x01)<<31)
-#define SDR0_SDSTP0_ENG_DECODE(n)	((((unsigned long)(n))>>31)&0x01)
-#define SDR0_SDSTP0_SRC_MASK		0x40000000
-#define SDR0_SDSTP0_SRC_PLLOUTA		0x00000000
-#define SDR0_SDSTP0_SRC_PLLOUTB		0x40000000
-#define SDR0_SDSTP0_SRC_ENCODE(n)	((((unsigned long)(n))&0x01)<<30)
-#define SDR0_SDSTP0_SRC_DECODE(n)	((((unsigned long)(n))>>30)&0x01)
-#define SDR0_SDSTP0_SEL_MASK		0x38000000
-#define SDR0_SDSTP0_SEL_PLLOUT		0x00000000
-#define SDR0_SDSTP0_SEL_CPU		0x08000000
-#define SDR0_SDSTP0_SEL_EBC		0x28000000
-#define SDR0_SDSTP0_SEL_ENCODE(n)	((((unsigned long)(n))&0x07)<<27)
-#define SDR0_SDSTP0_SEL_DECODE(n)	((((unsigned long)(n))>>27)&0x07)
-#define SDR0_SDSTP0_TUNE_MASK		0x07FE0000
-#define SDR0_SDSTP0_TUNE_ENCODE(n)	((((unsigned long)(n))&0x3FF)<<17)
-#define SDR0_SDSTP0_TUNE_DECODE(n)	((((unsigned long)(n))>>17)&0x3FF)
-#define SDR0_SDSTP0_FBDV_MASK		0x0001F000
-#define SDR0_SDSTP0_FBDV_ENCODE(n)	((((unsigned long)(n))&0x1F)<<12)
-#define SDR0_SDSTP0_FBDV_DECODE(n)	((((((unsigned long)(n))>>12)-1)&0x1F)+1)
-#define SDR0_SDSTP0_FWDVA_MASK		0x00000F00
-#define SDR0_SDSTP0_FWDVA_ENCODE(n)	((((unsigned long)(n))&0x0F)<<8)
-#define SDR0_SDSTP0_FWDVA_DECODE(n)	((((((unsigned long)(n))>>8)-1)&0x0F)+1)
-#define SDR0_SDSTP0_FWDVB_MASK		0x000000E0
-#define SDR0_SDSTP0_FWDVB_ENCODE(n)	((((unsigned long)(n))&0x07)<<5)
-#define SDR0_SDSTP0_FWDVB_DECODE(n)	((((((unsigned long)(n))>>5)-1)&0x07)+1)
-#define SDR0_SDSTP0_PRBDV0_MASK		0x0000001C
-#define SDR0_SDSTP0_PRBDV0_ENCODE(n)	((((unsigned long)(n))&0x07)<<2)
-#define SDR0_SDSTP0_PRBDV0_DECODE(n)	((((((unsigned long)(n))>>2)-1)&0x07)+1)
-#define SDR0_SDSTP0_OPBDV0_MASK		0x00000003
-#define SDR0_SDSTP0_OPBDV0_ENCODE(n)	((((unsigned long)(n))&0x03)<<0)
-#define SDR0_SDSTP0_OPBDV0_DECODE(n)	((((((unsigned long)(n))>>0)-1)&0x03)+1)
+#define SDR0_SDCS_SDD			(0x80000000 >> 31)
 
-#define SDR0_SDSTP1_LFBDV_MASK		0xFC000000
-#define SDR0_SDSTP1_LFBDV_ENCODE(n)	((((unsigned long)(n))&0x3F)<<26)
-#define SDR0_SDSTP1_LFBDV_DECODE(n)	((((unsigned long)(n))>>26)&0x3F)
-#define SDR0_SDSTP1_EBCDV0_MASK		0x03000000
-#define SDR0_SDSTP1_EBCDV0_ENCODE(n)	((((unsigned long)(n))&0x03)<<24)
-#define SDR0_SDSTP1_EBCDV0_DECODE(n)	((((unsigned long)(n))>>24)&0x03)
-#define SDR0_SDSTP1_MALDV0_MASK		0x00C00000
-#define SDR0_SDSTP1_MALDV0_ENCODE(n)	((((unsigned long)(n))&0x03)<<22)
-#define SDR0_SDSTP1_MALDV0_DECODE(n)	((((unsigned long)(n))>>22)&0x03)
-#define SDR0_SDSTP1_RW_MASK		0x00300000
-#define SDR0_SDSTP1_RW_8BIT		0x00000000
-#define SDR0_SDSTP1_RW_16BIT		0x00100000
-#define SDR0_SDSTP1_RW_32BIT		0x00200000
-#define SDR0_SDSTP1_RW_ENCODE(n)	((((unsigned long)(n))&0x03)<<20)
-#define SDR0_SDSTP1_RW_DECODE(n)	((((unsigned long)(n))>>20)&0x03)
-#define SDR0_SDSTP1_EARV_MASK		0x00080000
-#define SDR0_SDSTP1_EARV_EBC		0x00000000
-#define SDR0_SDSTP1_EARV_PCI		0x00080000
-#define SDR0_SDSTP1_PAE_MASK		0x00040000
-#define SDR0_SDSTP1_PAE_DISABLE		0x00000000
-#define SDR0_SDSTP1_PAE_ENABLE		0x00040000
-#define SDR0_SDSTP1_PAE_ENCODE(n)	((((unsigned long)(n))&0x01)<<18)
-#define SDR0_SDSTP1_PAE_DECODE(n)	((((unsigned long)(n))>>18)&0x01)
-#define SDR0_SDSTP1_PHCE_MASK		0x00020000
-#define SDR0_SDSTP1_PHCE_DISABLE	0x00000000
-#define SDR0_SDSTP1_PHCE_ENABLE		0x00020000
-#define SDR0_SDSTP1_PHCE_ENCODE(n)	((((unsigned long)(n))&0x01)<<17)
-#define SDR0_SDSTP1_PHCE_DECODE(n)	((((unsigned long)(n))>>17)&0x01)
-#define SDR0_SDSTP1_PISE_MASK		0x00010000
-#define SDR0_SDSTP1_PISE_DISABLE	0x00000000
-#define SDR0_SDSTP1_PISE_ENABLE		0x00010000
-#define SDR0_SDSTP1_PISE_ENCODE(n)	((((unsigned long)(n))&0x01)<<16)
-#define SDR0_SDSTP1_PISE_DECODE(n)	((((unsigned long)(n))>>16)&0x01)
-#define SDR0_SDSTP1_PCWE_MASK		0x00008000
-#define SDR0_SDSTP1_PCWE_DISABLE	0x00000000
-#define SDR0_SDSTP1_PCWE_ENABLE		0x00008000
-#define SDR0_SDSTP1_PCWE_ENCODE(n)	((((unsigned long)(n))&0x01)<<15)
-#define SDR0_SDSTP1_PCWE_DECODE(n)	((((unsigned long)(n))>>15)&0x01)
-#define SDR0_SDSTP1_PPIM_MASK		0x00008000
-#define SDR0_SDSTP1_PPIM_ENCODE(n)	((((unsigned long)(n))&0x0F)<<11)
-#define SDR0_SDSTP1_PPIM_DECODE(n)	((((unsigned long)(n))>>11)&0x0F)
-#define SDR0_SDSTP1_PR64E_MASK		0x00000400
-#define SDR0_SDSTP1_PR64E_DISABLE	0x00000000
-#define SDR0_SDSTP1_PR64E_ENABLE	0x00000400
-#define SDR0_SDSTP1_PR64E_ENCODE(n)	((((unsigned long)(n))&0x01)<<10)
-#define SDR0_SDSTP1_PR64E_DECODE(n)	((((unsigned long)(n))>>10)&0x01)
-#define SDR0_SDSTP1_PXFS_MASK		0x00000300
-#define SDR0_SDSTP1_PXFS_HIGH		0x00000000
-#define SDR0_SDSTP1_PXFS_MED		0x00000100
-#define SDR0_SDSTP1_PXFS_LOW		0x00000200
-#define SDR0_SDSTP1_PXFS_ENCODE(n)	((((unsigned long)(n))&0x03)<<8)
-#define SDR0_SDSTP1_PXFS_DECODE(n)	((((unsigned long)(n))>>8)&0x03)
-#define SDR0_SDSTP1_PDM_MASK		0x00000040
-#define SDR0_SDSTP1_PDM_MULTIPOINT	0x00000000
-#define SDR0_SDSTP1_PDM_P2P		0x00000040
-#define SDR0_SDSTP1_PDM_ENCODE(n)	((((unsigned long)(n))&0x01)<<6)
-#define SDR0_SDSTP1_PDM_DECODE(n)	((((unsigned long)(n))>>6)&0x01)
-#define SDR0_SDSTP1_EPS_MASK		0x00000038
-#define SDR0_SDSTP1_EPS_GROUP0		0x00000000
-#define SDR0_SDSTP1_EPS_GROUP1		0x00000008
-#define SDR0_SDSTP1_EPS_GROUP2		0x00000010
-#define SDR0_SDSTP1_EPS_GROUP3		0x00000018
-#define SDR0_SDSTP1_EPS_GROUP4		0x00000020
-#define SDR0_SDSTP1_EPS_GROUP5		0x00000028
-#define SDR0_SDSTP1_EPS_GROUP6		0x00000030
-#define SDR0_SDSTP1_EPS_GROUP7		0x00000038
-#define SDR0_SDSTP1_EPS_ENCODE(n)	((((unsigned long)(n))&0x07)<<3)
-#define SDR0_SDSTP1_EPS_DECODE(n)	((((unsigned long)(n))>>3)&0x07)
-#define SDR0_SDSTP1_RMII_MASK		0x00000004
-#define SDR0_SDSTP1_RMII_100MBIT	0x00000000
-#define SDR0_SDSTP1_RMII_10MBIT		0x00000004
-#define SDR0_SDSTP1_RMII_ENCODE(n)	((((unsigned long)(n))&0x01)<<2)
-#define SDR0_SDSTP1_RMII_DECODE(n)	((((unsigned long)(n))>>2)&0x01)
-#define SDR0_SDSTP1_TRE_MASK		0x00000002
-#define SDR0_SDSTP1_TRE_DISABLE		0x00000000
-#define SDR0_SDSTP1_TRE_ENABLE		0x00000002
-#define SDR0_SDSTP1_TRE_ENCODE(n)	((((unsigned long)(n))&0x01)<<1)
-#define SDR0_SDSTP1_TRE_DECODE(n)	((((unsigned long)(n))>>1)&0x01)
-#define SDR0_SDSTP1_NTO1_MASK		0x00000001
-#define SDR0_SDSTP1_NTO1_DISABLE	0x00000000
-#define SDR0_SDSTP1_NTO1_ENABLE		0x00000001
-#define SDR0_SDSTP1_NTO1_ENCODE(n)	((((unsigned long)(n))&0x01)<<0)
-#define SDR0_SDSTP1_NTO1_DECODE(n)	((((unsigned long)(n))>>0)&0x01)
-
-#define SDR0_EBC_RW_MASK		0x30000000
-#define SDR0_EBC_RW_8BIT		0x00000000
-#define SDR0_EBC_RW_16BIT		0x10000000
-#define SDR0_EBC_RW_32BIT		0x20000000
-#define SDR0_EBC_RW_ENCODE(n)		((((unsigned long)(n))&0x03)<<28)
-#define SDR0_EBC_RW_DECODE(n)		((((unsigned long)(n))>>28)&0x03)
+#if defined(CONFIG_440GP)
+#define CPC0_STRP1_PAE_MASK		(0x80000000 >> 11)
+#define CPC0_STRP1_PISE_MASK		(0x80000000 >> 13)
+#endif /* defined(CONFIG_440GP) */
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
+#define SDR0_SDSTP1_PAE_MASK		(0x80000000 >> 13)
+#define SDR0_SDSTP1_PISE_MASK		(0x80000000 >> 15)
+#endif /* defined(CONFIG_440GX) || defined(CONFIG_440SP) */
+#if defined(CONFIG_440EP) || defined(CONFIG_440GR)
+#define SDR0_SDSTP1_PAE_MASK		(0x80000000 >> 21)
+#define SDR0_SDSTP1_PAME_MASK		(0x80000000 >> 27)
+#endif /* defined(CONFIG_440EP) || defined(CONFIG_440GR) */
 
 #define SDR0_UARTX_UXICS_MASK		0xF0000000
 #define SDR0_UARTX_UXICS_PLB		0x20000000
@@ -1196,7 +1159,7 @@
 /*-----------------------------------------------------------------------------+
 |  Clocking
 +-----------------------------------------------------------------------------*/
-#if !defined (CONFIG_440GX) && !defined(CONFIG_440EP) && !defined(CONFIG_440GR)
+#if !defined (CONFIG_440GX) && !defined(CONFIG_440EP) && !defined(CONFIG_440GR) && !defined(CONFIG_440SP)
 #define PLLSYS0_TUNE_MASK	0xffc00000	/* PLL TUNE bits	    */
 #define PLLSYS0_FB_DIV_MASK	0x003c0000	/* Feedback divisor	    */
 #define PLLSYS0_FWD_DIV_A_MASK	0x00038000	/* Forward divisor A	    */
diff --git a/include/ppc4xx_enet.h b/include/ppc4xx_enet.h
index eacfb68..d6d33b6 100644
--- a/include/ppc4xx_enet.h
+++ b/include/ppc4xx_enet.h
@@ -131,7 +131,9 @@
 
 #if defined(CONFIG_440GX)
 #define EMAC_NUM_DEV	    4
-#elif (defined(CONFIG_440) || defined(CONFIG_405EP)) && defined(CONFIG_NET_MULTI)
+#elif (defined(CONFIG_440) || defined(CONFIG_405EP)) &&	\
+	defined(CONFIG_NET_MULTI) &&			\
+	!defined(CONFIG_440SP)
 #define EMAC_NUM_DEV	    2
 #else
 #define EMAC_NUM_DEV	    1
@@ -321,7 +323,7 @@
 #define EMAC_M0_WKE			    (0x04000000)
 
 /* on 440GX EMAC_MR1 has a different layout! */
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
 /* MODE Reg 1 */
 #define EMAC_M1_FDE		(0x80000000)
 #define EMAC_M1_ILE		(0x40000000)